Directorate Of Municipal Administration - Karnataka

32005376 purchase and installation of materials for the requirement for the purifcation of dry water at nekkudi kere chintamani town , supply and installation of following machinaries for sewage treatment plant at nekkundi kere. bar screen 1 no, sewage feed pumps 2 no, air blowe for collection mbbr, sludge tank & treated water tank 2 nos, coarse bubble air diffusers for collection, aeration sludge & treated water tank 1 no, fine bubble air diffusers for sbr tanks 1 and 2 1 no, sodium hypo dosing system 1 no, filter feed pump 2 no, sand filter in ms epoxy painted 1 no, activated carbon filter in ms epoxy painted 1 no, sludge pump 2 no, interconnected piping ( within battery limits ) 1 no, valves ( manul ) 1 no, electrical control panel 1 no, electrical accessories & cabling 1 job and instruments required to complete the work 1 job. all the above machinaries should be installed conforming to specifications. and as per the directions of the engineer in charge of the work....

Agriculture Produce Marketing Committee - Karnataka

31780765 quotation for supply of machinery equipments for stp , bar screen : supplying, installing, testing and commissioning of perforated stainless steel screen to avoid large sized inorganic floating impurities with ss304 tubes frame work. thickness of the ss perforated sheet is 1.5mm, ss304. perforation diameter of 15 mm. the screen is kept at inclined angle 45 degree to the horizontal. a ss basket of ss 304 with an attached arm of ss 304 pipe is provided for manual lifting of the screened materials. the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful.size : 750x1000 mm ( as required at site ) , raw sewage transfer pumps: supplying, installing, testing and commissioning of raw sewage pumps ( sewage submersible type ) along with cabling for pumps and floats, floats, nylon ropes for lifting and lowering, non return valves and all related accessories etc. complete. the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful., bio tower recirculation pumps: supplying, installing, testing and commissioning of bio tower recirculation pumps ( sewage submersible type ) along with cabling for pumps and floats, floats, nylon ropes for lifting and lowering, non return valves and all related accessories etc. complete. in two bio towers the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful., settler feeding pumps supplying, installing, testing and commissioning of settler sludge pumps ( sewage submersible type ) along with cabling for pumps and floats, floats, nylon ropes for lifting and lowering, non return valves and all related accessories etc. complete. the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful., settler sludge pumps: supplying, installing, testing and commissioning of settler sludge pumps ( sewage submersible type ) along with cabling for pumps and floats, floats, nylon ropes for lifting, non return valves and all related accessories etc. complete. the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful., filter feed pumps: supplying, installing, testing and commissioning of filter feed pumps ( open well submersible type ) along with cabling for pumps and floats, floats, nylon ropes for lifting, non return valves and all related accessories etc. complete. the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful., chlorine dosing system: designing, supply, erection, commission of the hypochlorite solution dosing unit with a flow range of 0 6 l / hour with diapharm type dosing pump, chemical storage drum of 50 l capacity, necessary electrical wiring and other related accessories etc. complete the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful., pressure sand filter: supplying, installation testing and commissioning of frp sand media filter of diameter 36 inches and hos 72 inches with uniform shell thickness for filtration of partially treated sewage water as per the technical specification along with pressure gauges, valves, air release valve, filter stand, drain release, sand, pebbles and gravel. the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful., activated carbon filter: supplying, installation testing and commissioning of frp carbon media filter of diameter 36 inches and hos 72 inches with uniform shell thickness for filtration of partially treated sewage water as per the technical specification along with pressure gauges, valves, air release valve, filter stand, drain release, carbon media. the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful., plant piping: supply and fixing upvc pipes sch 40 for plumbing of approved make and of required sizes as required at site with fittings of sch 40 ( such as tees, crosses, plugs, sockets, elbows, reducers, unions, flanges, sleeve pieces, check nuts, brackets, shoes etc. ) standard: astm d 1785 & astm d 2466. the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful., air vent pipeline: supply and fixing pvc pipe for air vent with length of 50 meters along with cowls on top diameter 6 , with fittings such as elbows, reducers, collars, brackets etc. the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful., bio tower media: supplying, installing, testing and commissioning of plastic media bio dek sheet form 1200 x 600 mm , black color, uv stabilized rigid pvc for bio towers : note: this item also include the cost of glue required to bond the media and place in the required arrangement including the labour involved for bonding the media and placement of media etc. including cost of hire charges of glue machine etc complete. the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful., nozzles: supply and fixing of non chocking water breaking 1 nozzles with 3diameter adjustable plate for required height setting using suitable threading and checknuts. these nozzles are to be installed within the bio towers of stp for effective breakage of water into droplets over the bio tower media along with necessary mta and etc., the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful., centrifugal air fans for bio towers: supplying, installing, testing and commissioning of inline centrifugal air fans of capacity 1200 cum / hr along with accessories to supply air including necessary flanges, bolts, electrical cable and conduit piping from the fan up to the control panel 3 phase / single phase power rating: upto 0.75 hp ( as required at site ) the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful., stp panel: along with board, door, single phase preventer, mcbs, two 15 amps plugs, indicators, ammeters, bolts, nuts, frame etc complete. the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful., electrical cables: supply and laying inter unit cabling for all equipments with necessary unarmoured cables with necessary termination lugs, glands etc complete. supply, laying and connecting of armoured 10 sqmm, 4 core cable for input power to the stp. the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful., cable trays: supplying and fixing cable trays to run the conduit pipes from the electrical equipments to the control panel including all necessary fittings with screws, anchor fastener etc complete. the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful., ultra filtration system of 8 cum / hr capacity : including bag filter, feed water pump, backwash pump, clean inplace pump, dosing pump uf feed line and backwash line, uf membrane with flux 45 lmh, single bore capillary, ms skid system, control panel, instrumentation, inter connecting piping and fittings and all allied accessories. the rates inclusive of cost all materials, labour charges, all leads and lifts, transportation to the workspot, hire charges of machineries and equipements including accidental charges if any and work is to be carried out as per requirements of the unit and capable of running the unit successful....

Karnataka Cooperative Milk Producers Federation Limited - Karnataka

29524055 tenders are invited from companies registered under irda towards renewal of various policies like plant and machinery, building, milk products, coal, coal ash, general stores materials, packing material, electronic equipments, vehicles and money policy for the period 23.11.2020 to 22.11.2022. renewal of various policies 1. plant & machinery includes following sections a ) rmrd – can conveyor, can washer electronic & mechanical weigh scales with weigh bowls, s.s. pipelines, ss milk pumps, 10000 liters cap: l&t milk chiller etc. b ) milk processing section 1 ) west falia cream separators – 2 nos. 2 ) apv milk pasteurizer cap: 10000 lts / hr – 1 no. 3 ) idmc cream pasteurizer cap: 2000 lts / hr 1 no. 4 ) homogenizer rannie cap: 2000 lts / hr – 1 no. 5 ) s.s. pipeline, steam & water pipelines, valves with fitting – 1 set. 6 ) electrical motors – 10 nos. 7 ) electrical panel board – 02 nos. 8 ) cream storage tank with mountings & agitator electrical motor cap: 5000 lts – 2 nos. 9 ) chilled water storage tank ( hmst ) – 1 no. 10 ) milk storage tanks with mountings & agitator electrical motor cap: 15000 lts – 6 nos. 11 ) automation control panel – 3 nos. 12 ) air compressor ir make – 03 no c ) butter churn room 1 ) butter churn make: l&t type uoh cap: 10000 with electrical motor gb – 01 no. 2 ) butter & butter milk trolley – 3 nos. 3 ) butter packing machine – 1 no. 4 ) electrical panel board – 1 no. d ) ghee section: 1 ) ghee boiler with accessories – 01 no. 2 ) ghee settling tank cap: 4500 – 02 nos. 3 ) ghee storage tank cap: 4500 – 02 nos. 4 ) ghee packing machine make: mb – 03 nos. 5 ) butter melting vat – 01 nos. 6 ) ghee filling machine – 01 no. 7 ) ghee clarifier make: alfa laval – 01 no. 8 ) s.s. pipe lines, steam & water pipelines with valve & fittings – 01 set 9 ) electrical panel board – 01 no. e ) powder plant 1 ) make l&t triple effect falling film evaporator plant – vapoun separator – 03 nos. & calandria – 3, thermo compressor, steam jet injecter with all accessories & fittings 2 ) tubuler heater – 02 nos. 3 ) milk holding tanks –0 2 nos. 4 ) ss milk pumps – 09 nos. 5 ) temperature controller and pressure controller instrument panel. 6 ) ss pipelines valves & fittings 7 ) powder draying chamber with accessories. 8 ) niro f 35 atomizer type abc with electrical motor 9 ) air supply fan & air exhaust fan with motor. 10 ) conveying air fan with motor. 11 ) conveying cyclone – 1 no. 12 ) main cyclone – 1 no. 13 ) stream air heated banks – 08 nos. 14 ) rotary valves with motors – 3 nos. 15 ) s.s. milk pumps – 1 no. 16 ) s.s. pipe lines with valves & fittings 17 ) steam header with valves, steam line 18 ) s.s. ducts for powder 19 ) powder hopper with electrical motor 01 no. 20 ) vacuum pumps make: mazda controls with 20 hp electrical motors – 2 nos. 21 ) electromagnetic hammers with control panel. f ) refrigeration section 1 ) 9x9 heavy duty ammonia compressors make: frick – 1 nos. 2 ) kirloskar slip ring electrical motors, 100 hp – 1 nos. 3 ) oil immersed starters – 1 nos. 4 ) oil separator – 3 nos. 5 ) evaporation coil with accessories for ibt tank – 2 sets. 6 ) chilled water tank – 02 nos. 7 ) liquid separators with necessary valves – 3 nos. 8 ) chilled water headers – 3 nos. 9 ) chilled water pumps – 3 nos. 10 ) condenser pumps – 3 nos. 11 ) air compressor – inger sol rand 2 nos. with suitable electrical motors and receives 12 ) mcc panel board – 2 nos. 13 ) aunti room ( cold room ) – 01 nos. 14 ) deepfreeze – 02 nos. 15 ) air cooling units with electrical motors & starters – 5 nos. 16 ) frp cooling tower with motors and accessories make: paharpur with rcc sump cap: 190 tr – 2 nos. 17 ) m.s. pipelines with fitting valves – 1 set 18 ) frick make, vilter compressor 42 xl with control panel board–1 no 19 ) kirloskar make, kcx6 compressor with control panel board – 1 no 20 ) kirloskar make, kcx31 compressor with control panel board & with accessories and filling – 1 no 21 ) evaporative condenser, make: evapco. cap:125 tr – 2 nos 22 ) ibt for tank 2016 rmt with accessories & filling 1 set 23 ) evaporator coils with all accessories for ibt tank 1 set 24 ) cold diffuser for deepfreeze 6tr each – 4 nos 25 ) oil separator – 3 nos. 26 ) ammonia receiver – 02 nos 1000 ltrs & 2000 ltrs capacity 27 ) chilled water pumps – 3nos. 28 ) chilled water headers – 1 nos. 29 ) mcc panel board – 3 nos 30 ) chilled water tank 1 no 31 ) water softener plant cap:10, 000 ltrs with complete piping & all accessories 01 no g ) work shop & pump house 1 ) lathe machine 1 no. 2 ) royal drilling machine – 1 no. 3 ) mono block pump hp 10 02 nos 4 ) mcc panel boards – 2 nos. 5 ) submersible pump set with starter elc. control panel 1 no. 6 ) arc welding generator make: advani – 1 no. 7 ) arc welding transformer – 1 no. 8 ) welding machine, make – ador 9 ) chap saw machine, make dewalt h ) effluent treatment plant equipments 6 ) primary setting tank 7 ) aerator tank 8 ) etp discharge waste pump – 2 no. 9 ) sludge pumps with motor – 2 nos. 10 ) electrical control panel board with starter 11 ) collection tank– 1 nos. 12 ) secondary settling tank – 1 no. 13 ) rcc sludge draying beds – 4 nos. 14 ) discharge water pump – 2 nos. 15 ) final treated water tank – 1 no. 16 ) sludge transformer pump – 2 no. 17 ) feed filling pump – 2 no. 18 ) raw water pump – 2 no. 19 ) clarifier with gear box motor 20 ) air diffuser blower – 02 no make: everest blower, model: 610, 1 ) s.no :eb17092434 b and 2 ) eb17092435. i ) boiler house 1 ) multi thermal coal fired, water tube boilers with valves fitting & accessories & mountings, cap: 2800 kg / hr. – 3 no’s mys 1419, mys 1406 & mys 1418 2 ) id fan with motors – 3 nos. 3 ) fd fan with motors – 3 nos. 4 ) m.s. chimney, 62 feet height with foundation – 3 nos. 5 ) feed water pumps with motors – 3 nos. 6 ) m.s. feed water tank – 1 no 7 ) water softener plant and filter plant – 1 no 8 ) air pollution control equipments for boiler with ducts & motor – 2 nos. 9 ) mcc control panel board – 2 nos. j ) power house & d.g. room 1 ) main electrical control panel board make: ltlk – 1 no. 2 ) step down transformer make: hbb cap: 500 kva, 33 kv / 430v – 02 nos. sl. no. ( i ) ih – 8617 ( ii ) ih – 8618 3 ) oil circuit breaker – 1 no. 4 ) 33 kv ocb control panel 5 ) power capacitor banks 6 ) main lighting distribution board 7 ) d.g. set make: cummins with stan ford alternator 250 kva – 01 no., s.no.25297389 8 ) d.g. set kirloskar cummins with kirloskar alternator 180 kva – 2 nos, s.no.1 ) 25219582 2 ) 25219858 9 ) change over panel 630 a – 2 nos. 10 ) control panel for all 3 d.g sets k ) laboratory equipments 1 ) kjeldhal unit kel plus 01 no. automatic micro:250 ml, block pc compatible , digestion system model: kel 04 lrts 01 continuous butter making machine make : hmt, cap : 800 kgs / hr 02 alfa laval milk pasteurizer cap: 10000 lts / hr – 1 nos. 03 repute cream pasteurizer cap: 3000 lts / hr – 1 no. expandable to 5000 lts / hr 04 ghee sachet packing make: advance packing, single head mechanical type – 01 no 05 ghee sachet packing machine to pack 50 ml and 100 ml ghee, make : packera 06 frick make vilter compressor 456xl with electrical motor and soft starter, oil separators etc model : 456xl, si no.632 07 new boiler house ( 5 tph ) 1 ) make : industrial boilers ltd capacity: 5000 kgs / hrs – 1 no, reg no: ktk 5185 2 ) with accessories like id fan with motor, fd fan with motor, m.s.chimeny, 100 ft height with foundation, feed water pumps with motor, m.s feed water tank, water softener plant with pump motor, air pollution control equipment with ducts – 2 no motors ( aph, multi cyclone dust collector , bag filter ) , m.c.c. / p.l.c control panel board. 3 ) coal handling system includes coal crusher with motor, belt conveyer with motor, bucket elevator with motor & gear box, coal bunker, air blower for coal crusher with motor & dust. 08 equipments for new products 1.flavoured milk bottle filling machine with air compressor. make: packera 2. bottle washing machine make: packera 3. crown capping machine, make: packera. 4. bottle sterilizer for sfm, make: rozi engg pune 5. ss conical bleding machine with gear box & electrical. motor. make: surabee 6. inject printer, make: markem image 7. pulverizer make: surabee 8. mysore pak kettle tilting type make : fansbrow erectors 9. skid mounted pasteurizer with homogenizer make : indotech, cap : 500 ltr 10. khova pan with s.s hood for exhaust : 04 nos make : milk mack, cap : 120 ltrs 11. chakka making machine make : solar arks, cap : 80 kgs 12.shrink tunnel machine, make: amar packaging 09 mcc electrical panel board – 02 nos for evapator & dryer section with vfd 10 ink jet printer with accessories , make: control print nos:02 11 winding & rewinding machine make: krishna engineering works, ahmadabad 01 power transformers make: hindustan brown boveri. 500 kva, 33kv / 433v s.no. 1. ih – 8617, 2. ih – 8618. along with power house mcc l&t make switch gear sy24203. 02 diesel generator sets engine make: kirloskar cummins, cap : 180 kva bhp: 231 rpm: 1500 type: nt –743 g, s.no. 25219582 ii. 25219858 alternator, make: kirloskar electronic co, kva: 180 type: 4ab 280 / e2 s.no. 1. 9620708 23 2. 9620708 29. along with electrical panel board with synchronizer. 03 diesel generator set engine , cap:250 kva make: cummines india model: nt – 855 65 bg cap 250 kva sl.no: 25297389, alternator make: stamford type hc44ci s.no. 04090697 sed 250. along with electrical control panel board, s.no.978 1 and change over switches, make : load control india pvt ltd., blr 04 atomizer make: niro type f 35 abc 06 s.no.1557 05 milk separators make: west falia type: mta: 90 01 024 s.no. 1. 1662518 2. 1662519 06 ammonia compressors make: frick type: hd, size: 9x9 i ) 9 en – 171 feb 79 07 air compressor in refn section make: ingersoll rand model:268 n sl.no.783000 08 vacuum pumps double stage water ring type make: mazda controls. type: cr 215 / 15 hp, rpm:1440 pressure / vacuum –720mm s.no. 1058 2. c 249 09 ghee clarifier ( separator ) make: alfa laval cap: 1000 ltrs / hrs. type: vlb 108, s.no.409 203 with electrical motor. make” abb 1 hp 3 phase, rpm 1380 10 air cooled air compressor equipped with belt geared, slide rail make: ingersoll rand model: 2545x10 s.no. 8044361. 11. vilter compressor, make : frick model : 456 – 42 xl sl. no. 130 with accessories 12. vilter compressor, make : frick, model : 456xl, si no.632 with accessories 13 40 mt capacity weigh bridge. make : elite, si no.110301, model : knl40 14 kirloskar make, kcx6 compressor with control panel board & accessories and fittings 1 no 15 kirloskar make, kcx31 compressor with control panel board & accessories and fittings 1 no 16 ammonia receiver – 1000 ltrs, 17 ammonia receiver – 2000 ltrs, 01 make: kirloskar slip ring induction motor hp 100 rpm: 1465 with mcc electrical panel board s.no. 2770751 6 in refrigeration section 02 make: hbb hp 60, rpm 1455 s.no.306807 with electrical panel board in powder plant. 03 make: hbb hp 60, rpm 1455 s.no.183158 with electrical panel board in powder plant. 04 make: hbb hp: 40, rpm 1450 s.no.306771 with electrical panel board for atomiser 05 make: hbb.hp: 30, rpm 1455 s.no. 213813 with electrical panel board for atomiser. 06 make: hbb, hp: 30, rpm 1455 s.no.304093 with electrical panel board for atomiser. 07 make: crompton greaves, hp: 40, rpm: 1465, 1 ) s.no.nadm25se. 2 ) nadm24se.connected to air blower in etp 08 make: crompton greaves, hp: 40, rpm: 1465, s.no.nadm24sc. connected to 5.0tph id fan 09 make: crompton greaves, hp:25, rpm: 2920, s.no.nadj42 and s.no:18.5ke2 connected to 5.0 tph fd fan 10 make: crompton greaves, hp: 30, rpm: 2965, s.no.nadm24sc 1 no. s.no : 0217 m701694. 11. make: siemens hp:60 s.no.8 / 64308989 with electrical panel board in refrigeration section. 12. make: hbb, hp:17 / 25 rpm 980 / 1470, s.no. 209031 with electrical panel board. connected to butter churn. 13. make: hbb, hp:17 / 25 rpm 980 / 1470, s.no. 571945 with electrical panel board connected to butter churn. 14. arc welding generator make: advani, rpm:2850, model: teledyne k320, 15kw 15. electrical motor, make : kirloskar, hp : 30, si no.ia 148 / s 144 for powder plant 16. electrical motor, make : kirloskar, hp : 30, si no.ia 149 / s 180 for powder plant 17. electrical motor, make : siemens, hp : 120, si no.n8 64467779 with soft starter and electrical panel board for refrigeration 18. electrical motor, make : abb, hp : 60, sino.3g1j14260001115185 with electrical panel board and softener starter for refrigeration 19. electrical motor, make : abb, hp : 120, sino.2g2j18120090080214 with electrical panel board and softener starter for refrigeration 01 02 03 04 a ) boilers make:thermax ( multitherm fuel water tube boiler ) – 03 nos rs.45lakhs cap: 2800 kgs / hrs each working pressure 15 kg / cm2 hydraulic pressure 22 kg / cm2 reg.no.mys 1419 reg.no.mys 1406 reg.no.mys 1418 b ) fbc boiler with accessories make: industrial boiler ltd. capacity: 5 tph reg no: ktk 5185 c ) 2klph reverse osmosis plant with accessories make: dexter water tech. d ) personnel – 20lakhs e ) property 3rd party 15lakhs bottle sterilizer, make: rozi ghee boiler with accessories make:indigeous cap:800 kg / per batch khova pan 01. universal jeep make: mahindra & mahindra registry no. cnq 3599 2200 cc model 1979 02. bajaj tempo trax registry no. ka 28 m 1516 chesses no. tx 939270 c 96 engine no. 616 969 141710 01. computer with printer, key board monitor. 1. monitor make a ) mmt3css00153714ddc4202 ( md sir room ) b ) mmlxkss00993111b7f4231 ( admn dept ) c ) aocwhf2e2057567 ( admn dept ) d ) mmlyoss00492000e138507 ( weigh bridge ) e ) etlbf080080360187a4200 ( weigh bridge ) f ) 41704657242 ( fgs dept ) g ) mmt3css00153714deb4202 ( qc dept ) h ) aockhf2e4257153 ( qc cc tv ) i ) cn 09wmp772872 68bddyu aoo ( store dept ) j ) aocahf2e1951542 ( pur dept ) k ) mmlxnss0024170b5ec4200 ( mkt dept ) l ) 6125bg004740c ( accts dept ) m ) 616011991314 ( accts dept ) n ) 52000607042 ( engg dept ) o ) mmlxnss00474402f874214 ( prod dept ) p ) mmlyoss00471602f928507 ( accts dept ) q ) 3cq94319q3 ( accts dept ) r ) ev226hql ( engg dept ) 2. cpu si no. a ) uxvjssip49f4804226 ( md sir room ) b ) uxvjssio89e3729995 ( md sir room ) c ) uxvjssl128e2608516 ( admn dept ) d ) uxbc7sia74j3991217 ( admn dept ) e ) uxbc7sic33k0519478 ( weigh bridge ) f ) co74a2231929 ( weigh bridge ) g ) uxvjssl128e2608530 ( fgs dept ) h ) uxvjssip49f4804205 ( qc dept ) i ) uxvjssl128e2608478 ( mkt dept ) j ) uxvjssl128e2608474 ( pur dept ) k ) uxvjssid10f4338465 ( accts dept ) l ) 6123aa402354 ( accts dept ) m ) 5123aa402481 ( store dept ) n ) uxvjssik83f2433932 ( engg dept ) o ) uxb1jsie01h4497513 ( prod dept ) p ) uxb1jsi561h1985911 / wo#0775 ( accts dept ) q ) ina949qwpl ( accts dept ) r ) uxbc7sie62k1180540 ( engg dept ) 02. colour television make: sony, 42” lcd. 03. colour television make: haier, 42” lcd for cc tv 1. cpu acer a ) uxvjssl089e3429995 04. tata sky disc with receiver nds.no:5281027935949315, 2641331889062584 01. milk products a ) skimmed milk powder b ) whole milk powder b ) butter c ) ghee d ) sterilized flavoured milk in 200 ml bottles e ) nandini jamun mix in 200 gm packets f ) nandini badam powder in 200 gm pckts g ) mysore pak h ) shrikhand i ) dharwad peda j ) khova 02. coal in open yard 03. coal ash in open yard 04 fly ash in open yard 05. general stores materials items; engineering spares electrical spares, production procurement, laboratory chemicals, equipments and machineries. 06. packing materials kraft paper bags, poly liners rolls, corrugated boxes, for various products, duplex cartoons, 15 kg ghee tins 25 kg liners, nandini ghee packing materials, new products packing materials etc. 01. cash in safe and cash box in our factory ddil, asangi at any single time 02. money policy ( money in transit ) in factory at single time....

National Institute Of Technology - Karnataka

28879630 cleaning of rcc sump tanks and overhead tanks by using mechanical means like high pressure jet machine for cleaning of tanks side walls bottom, subersible pump set and sludge pump set with hose pipe for dewatering and removal of all sludge, mud water, dirt etc....

National Institute Of Technology - Karnataka

25920763 tender for cleaning the sump tanks of pump house &rcc overhead tank of campus cleaning of rcc sump tanks and overhead tanks by using mechanical means like high pressure jet machine for cleaning of tanks side walls, bottom, submersible pump set and sludge pump set with hose pipe for de watering and removal of all sludge, mud water, dirt etc. and finally applying uv light treatment for killing suspended bacteria etc. including cost of all labors with safety measures and transportation of machines etc. complete.. a) near english medium school 1,20,000 ltr capacity rcc over head tank b) near english medium school 90,000 ltr capacity rcc over head tank c) near english medium school 2,00,000 ltr capacity rcc sump tank d) near gym 1,20,000 ltr capacity rcc over head tank e) circular sump tank 9,00,000 ltr capacity in pump house f) circular sump tank 4,50,000 ltr capacity in pump house g) circular sump tank 7,00,000 ltr capacity in pump house h) rectangular sump tank 70,000 ltr capacity in pump house ...

Bruhat Bangalore Mahanagara Palike - Karnataka

25637618 fixation of rate for procurement of stp plant equipments for the work of construction of stp balance work in ward no44 1. m.s. bar screen, supplying of bar screen of 1 nos. so as to remove the large sized particles present in the sewage water. stainless steel perforated, bar screen opening of 10mm,size: 600mm x 600mm,make: global. with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 2. raw sewage pumps: supplying of 2 nos. (one working + one standby) submersible type raw sewage water pumps to pump sewage from equilisation sump to aeration tank at 5.0 cu.m / hr flow rate. the pump shall be coupled to adequate h.p. electrical motor, the pump shall be suitable for solid handling capacity of 32 mm. the pump shall be suitable for the following requirements:flow rate 5.0 cu.m / hr, head 12 15 mtr, make : kirloskar / wilo/equivalent with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 3. fine bubble air diffusers: supply of required number of fine buuble air diffusers in eqt and required number of membrane type fine bubble air diffusers in sbr tanks. of size 90mm dia x 1000mm long epdm tubular membranes. make: equivalent. with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 4. coarse bubble diffusers: : supplying of coarse bubble duffuser with 80 mm dia pvc tubular membranes. make: equivalent with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 5. air blowers : (1 w + 1s) : supplying of 2 nos. (one working + one standby) rotary twin / tri lobe design type air blower complete with motors, pulleys, one piece rigid ci casing and side plates, silencer, base plate, anti friction bearings, rotary oil sealings having horizontal configuration.the blower shall be suitable for the following:flow rate 220.00 cu.m / hr, flow pressure 0.50 kg / sq. cm, head 4 mtr,1 no. pressure guage 4 dial with needle valve tee and fittings. make : tmvt / usha, motor for airblower to be provided / included with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 6. acoustic cost: (for air blowers)supply of sound proof acoustic hoods for air blowers of usha make as per below technical specification cap in type system with suitable for above air blowers with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 7. decanter mechanism: supplying of decanter mechanism as per system requirement with sutibale size electrical acutated valve with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 8. sludge transfer pumps: supplying of 2 no (one working + one standby) submersible type slude transfer pump at 2cu.m / hr flow rate @ 10 mtrs head. the pump shall be coupled to adequate h.p. electrical motor,. the pump shall be provide with suitable enclosure with strainer arrangement for the protection submersible pumps.the pump shall be suitable for the following requirements:flow rate 2 cu.m / hr, head 10 12 mtr, make : kirloskar / equivalent with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 9. part b teritary treatment 100.00 cu.m / day operating duration 10hrs: filter feed pump: supplying of filter feed pump consisting of 2 nos. (one working + one standby) monobloc type filter feed pumps for pumping decant water through sand pressure filter and finally to treated water sump the pump shall be coupled to the adequate h.p. electrical motor and shall be mounted on a common base frame with mani fold. the pump shall be suitable for the following requirements:flow rate 5 cu.m / hr, head 30 40mtr, make : kirloskar / equivalent with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 10. submersible dewatering transfer pump: supplying of dewatering pump consisting of 2 nos. (one working + one standby) submersible type dewatering pumps for pumping treated final water tank 1 to tank 2. the pump shall be provide with suitable enclosure with strainer arrangement for the protection submersible pumps. the pump shall be suitable for the following requirements:flow rate 10cu.m / hr, head 20 25mtr, make : kirloskar / equivalen / ksb with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 11. irrigation submersible pump: supplying of irrigation pump consisting of 1no. submersible type irrigation pumps for pumping treated final water tank 2 to garding the pump shall be suitable for the following requirements:flow rate 05cu.m / hr, head 10mtr, make : kirloskar / equivalen / ksb with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 12. ms sand pressure filter: supply of sand pressure filter for filtration of suspended impurities in treated sewage water. the filter shall be suitable for 10.0 cu.m / hr flow rate and designed to remove suspended particals / impurity in treated sewage water.the spf shall be designed for a specific velocity of 12 m3 / hr / sq.m area and the approx size shall not be less than 800 mm dia. the sand pressure filter unit shall comply with the following technical requirements:flow rate 10.00 cu.m / hr, back wash duration 15 minutes, painting internal two coats of anti corrosive epoxy paint, painting external two coat of redoxide primer and above that a layer of two coats of enamel paint to be done to give the finishing.filtering media sand/pebbles, pressure drop across unit. 0.7kg/ sq.cm (max), inlet turbidity 1.00 as ntu, dia of sand pressure filter unit 800 mm dia.further, the sand pressure filter unit shall comprise of the following: the sand pressure filter vessel shall be fabricated out of ms plate (crca sheet of global make) not less then 6mm thick with dish ends out of 8 mm thick plate and painted internally with two coats of anticorrosive epoxy paint after sand blasting and externally with two coats epoxy primer followed by two coats of enamel paint of approved colour.the sand pressure filter shall be fitted with top inlet distribution and bottom collecting system.pressure gauge with needle valve shall be provided at inlet and out let of sand pressure filter. v notch of suitable size fabricated out of 6 mm ms plate and finished with hot dip galvanizing to 100 microns inlcuding marking of flowrates indication for monitoring of backwash of sand pressure filter. initial charge of underbed and multigrade filtering media as required. complete set of valves, pressure gauge with needle valve and frontal piping at inlet, outlet backwash and drain out point etc., with gi b class pipes (make: global). concrete bed/pedestals of suitable size and thickness in cement concrete 1:2:4 for mounting the filter base with anchor fastener, bolts and nuts and neatly finished smooth with floating coat of cement mortar. with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 13. ms activated carbon filter (acf):supply of activated carbon filter for filtration and removal of colour and odour in treated sewage water. the filter shall be suitable fo 10.0 cu.m / hr flow rate and designed to operate for 10 hours. the acf shall be designed for a specific velocity of 12 m3 / hr / sq.m area and the approx dia shall not be less than 800 mm dia . the activated carbon filter unit shall comply with the following techinical requirement.flow rate 10.50 cu.m / hr, back wash duration 15 minutes, painting internal two coats of anti corrosive epoxy paint, painting external two coat of redoxide primer and above that a layer of two coats of enamel paint to be done to give the finishing. filtering media activated carbon, pressure drop across unit. 0.7kg / sq.cm (max), dia of activated carbon filter unit 800 mm dia.further the activated carbon filter unit shall comprise the following. the activated carbon filter vessel shall be fabricated out of ms plate (make:global) not less then 6mm thick with dish ends out of 8mm thick plate and painted internally with two coats of anticorrosive epoxy paint after sand blasting and externally with two coats epoxy primer followed by two coats of enamel paint of approved colour. the activated carbon filter shall be fitted with inlet distribution and bottom collecting system. pressure gauge with needle valve shall be provided at inlet and out let of activated carbon filter. v notch of suitable size fabricated out of 6 mm ms plate and finished with hot dip galvanizing to 100 microns inlcuding marking of flowrates indication for monitoring of backwash of activated carbon filter. initial charge of underbed and multigrade filtering media as required. complete set of valves, pressure gauge with needle valve and frontal piping at inlet, outlet backwash and drain out point etc., with gi b class pipes (make: tata / jindal). concrete bed/pedestals of suitable size and thickness in cement concrete 1:2:4 for mounting the filter base with anchor fastener, bolts and nuts and neatly finished smooth with floating coat of cement mortar. with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 14. chlorinator: supply of electronic chlorine dosing unit with automatically operated dosing pump etc. the unit shall comprise of the following: one no. single moulded frp cylindrical type chemical solution tank of 50 litres capacity having detachable lids with moulded inserts for mounting of pumps and stirrer.one on. electronic diaphragm type positive displacement pump of asia lmi make, for chemical dosing with plastic head. the electronic pump shall be operated on 220v single phase supply and shall be mounted directly on the tank top.complete set of pipes, valves and fittings, foot valve magnetic float switch to trip the dosing pump at low level of chemical in the tank.the free chlorine content in the filtered water shall not be less than 0.5 ppm.concrete bed/pedestals of suitable size and thickness in cement concrete 1:2:4 for mounting the doser base with anchor fastener, bolts and nuts and neatly finished smooth with floating coat of cement mortar. the pump shall be suitable for the following requirements:min. actuating pressure 0.3 kg/sq cm, max. working pressure 0.5 kg/sq cm, max. temperature 50 degree centigrade, dosing flow range as per system requirement, head 5 10 mtr. with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 15. mcc panel: supply of combined / common motor control center panel (mccp) for filtered water pumps. the mcc shall be sheet steel fabricated, finished with powder coating of approved color, and of floor mounted, free standing cubicle type with incoming mcc tp and n bus bars and outgoing with fuse switch units, starter relays, over load, uv earth fault protection with time delay sequence operator etc. the panel shall have voltmeter, ammeter and indicating lamps on the incoming side only indicating lamps for the pumps on outgoing side to indicate the operation mode. the panel shall be complete in all respectsand prior to the supply, fabrication drawing shall be submitted for consultants approval.the rate quoted shall be inclusive of the following: earthing for panels .dry run protection arrangement for the following : raw sewage pump, air blowers & motors: return sludge pump, screw pump, filter feed pump , filter feed pump for ultra filtration , ultrafiltration backwash pumps, audio / visual alarm indication in the event of malfuntioning of stp with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 16. plant piping: supplying of the necessary piping works for the stp consisting of interconnecting piping, fittings, valves within the battery limit of the sewage treatment plant moc of the piping including all fittings like tees, elbows, bends, collars, coupling, etc jointing with rubber ring / solvent cement followed by application of leak proof adhesive like frp paste with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 17. sludge hadling centrifuge system:. top dischargebasket centrifuge.three points pendulum suspended.outer body – ms/ epoxy painted. foot mounted, crompton greaves make. centrifuge force depends on material density.paddle disc brake arrangements to stop the basket. limit switches for lid. foundation bolts provided. p.p. filter bag provided. with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., 18. installation and commissioning of the 100 kld stp with all the above electro mechanical equipments . with includes all labour charges trasportion charges, installation charges and all other taxes with all lead and lift as per the approval of engineer incharge., ...

Karnataka Power Corporation Limited - Karnataka

25163614 procurement of spares for centrifugal pumps at ytps 1. coupling for cw make up pump, 2. fastener set for cw pump, 3. coupling set for swp, 4. fasteners set for swp, 5. casing ring (chp dust suppres), 6. shaft sleeve (chp dust suppre), 7. gland for chp dsp, 8. sleeve nut (chp dust suppress), 9. bearing lock nut (chp dust su), 10. inboard bearing house (chp du), 11. outboard bearing house (chp d), 12. bearing cover (chp dust suppr), 13. bearing lock washer (chp dust), 14. adopter, 15. o ring (sleeve) for chp dsp, 16. stuffing box for chp dsp, 17. air cock for chp dust pump, 18. braided hose for chp dust supp, 19. coupling set for chp dust supp, 20. fasteners set for chp dust sup, 21. lock nut (sludge transfer pum), 22. lock washer (sludge transfer ), 23. ratchen pin (1set =2nos), 24. ratchen collar, 25. bearing collar, 26. bearing cap (sludge transfer ), 27. bearing housing (sludge trans), 28. lock nut (sludge pump), 29. gland (1no=2 halves), 30. gland housing, 31. gland ring, 32. drive column pipe, 33. line column pipe, 34. pump column pipe, 35. strainer, 36. bush housing, 37. impeller nut (sludge transfer), 38. volute casing for stp, 39. coupling set for sludge transf, 40. casing cover (etp supply pump), 41. bearing housing lantern, 42. bearing bed (etp supply pump), 43. bearing cap (outer) (etp supp), 44. bearing cap (inner) (etp supp), 45. oil seal (for etp pump), 46. grooved nut and lock washer, 47. coupling set for etp pump, 48. deflector for etp, 49. constant level oiler for etp, 50. gland for etp, 51. pressure ring for etp, ...

Karnataka Power Corporation Limited - Karnataka

24549152 procurement of spares for centrifugal pumps at ytps 1. coupling for cw make up pump, 2. fastener set for cw pump, 3. coupling set for swp, 4. fasteners set for swp, 5. shaft ( chp dust suppression p ) , 6. casing ring ( chp dust suppres ) , 7. shaft sleeve ( chp dust suppre ) , 8. gland for chp dsp, 9. sleeve nut ( chp dust suppress ) , 10. bearing lock nut ( chp dust su ) , 11. inboard bearing house ( chp du ) , 12. outboard bearing house ( chp d ) , 13. bearing cover ( chp dust suppr ) , 14. coupling key ( chp dust suppre ) , 15. bearing lock washer ( chp dust ) , 16. adopter, 17. o ring ( sleeve ) for chp dsp, 18. stuffing box for chp dsp, 19. air cock for chp dust pump, 20. grease nipple for chp dust pum, 21. eye bolt for chp dust supp pump, 22. braided hose for chp dust supp, 23. coupling set for chp dust supp, 24. fasteners set for chp dust sup, 25. lock nut ( sludge transfer pum ) , 26. lock washer ( sludge transfer ) , 27. ratchen pin ( 1set =2nos ) , 28. ratchen collar, 29. bearing collar, 30. bearing cap ( sludge transfer ) , 31. bearing housing ( sludge trans ) , 32. lock nut ( sludge pump ) , 33. gland ( 1no=2 halves ) , 34. gland housing, 35. gland ring, 36. drive shaft ( sludge transfer ) , 37. line shaft, 38. pump shaft ( sludge transfer p ) , 39. drive column pipe, 40. line column pipe, 41. pump column pipe, 42. coupling sleeve set, 43. strainer, 44. shaft sleeve ( p.end ) , 45. bush housing, 46. impeller nut ( sludge transfer ) , 47. gasket set ( 1set=15 nos ) , 48. volute casing for stp, 49. coupling set for sludge transf, 50. casing cover ( etp supply pump ) , 51. pump shaft ( etp supply pump ) , 52. bearing housing lantern, 53. bearing bed ( etp supply pump ) , 54. bearing cap ( outer ) ( etp supp ) , 55. bearing cap ( inner ) ( etp supp ) , 56. gasket ( brg cap outer ) for etp, 57. key ( coupling ) , 58. oil seal ( for etp pump ) , 59. grooved nut and lock washer, 60. coupling set for etp pump, 61. deflector for etp, 62. constant level oiler for etp, 63. key impeller for etp, 64. gland for etp, 65. gland packing set for etp, 66. pressure ring for etp, 67. shaft sleeve for etp, ...

Karnataka Power Corporation Limited - Karnataka

24288228 procurement of spares for centrifugal pumps at ytps 1. coupling for cw make up pump, 2. fastener set for cw pump, 3. coupling set for swp, 4. fasteners set for swp, 5. shaft (chp dust suppression p), 6. casing ring (chp dust suppres), 7. shaft sleeve (chp dust suppre), 8. gland for chp dsp, 9. sleeve nut (chp dust suppress), 10. bearing lock nut (chp dust su), 11. inboard bearing house (chp du), 12. outboard bearing house (chp d), 13. bearing cover (chp dust suppr), 14. coupling key (chp dust suppre), 15. bearing lock washer (chp dust), 16. adopter, 17. o ring (sleeve) for chp dsp, 18. stuffing box for chp dsp, 19. air cock for chp dust pump, 20. grease nipple for chp dust pum, 21. eye bolt for chp dust supp pump, 22. braided hose for chp dust supp, 23. coupling set for chp dust supp, 24. fasteners set for chp dust sup, 25. lock nut (sludge transfer pum), 26. lock washer (sludge transfer ), 27. ratchen pin (1set =2nos), 28. ratchen collar, 29. bearing collar, 30. bearing cap (sludge transfer ), 31. bearing housing (sludge trans), 32. lock nut (sludge pump), 33. gland (1no=2 halves), 34. gland housing, 35. gland ring, 36. drive shaft (sludge transfer ), 37. line shaft, 38. pump shaft (sludge transfer p), 39. drive column pipe, 40. line column pipe, 41. pump column pipe, 42. coupling sleeve set, 43. strainer, 44. shaft sleeve (p.end), 45. bush housing, 46. impeller nut (sludge transfer), 47. gasket set (1set=15 nos), 48. volute casing for stp, 49. coupling set for sludge transf, 50. casing cover (etp supply pump), 51. pump shaft (etp supply pump), 52. bearing housing lantern, 53. bearing bed (etp supply pump), 54. bearing cap (outer) (etp supp), 55. bearing cap (inner) (etp supp), 56. gasket (brg cap outer) for etp, 57. key (coupling), 58. oil seal (for etp pump), 59. grooved nut and lock washer, 60. coupling set for etp pump, 61. deflector for etp, 62. constant level oiler for etp, 63. key impeller for etp, 64. gland for etp, 65. gland packing set for etp, 66. pressure ring for etp, 67. shaft sleeve for etp, ...

Indian Navy - Karnataka

24167449 rfp for three years repair rate contract for evac vaccuum toilet system and sewage treatment plants for in ships and yard crafts at nsry karwar repair / routines of evac vaccuum toilet system and sewage treatment plants for in ships and yard crafts , part 1 vacuum toilet system evac vacuum toilet system ejector type ( ins aditya , ins subhadra and ins suvarna ) , vacuum pump , completed overhauling of pump , completed overhauling of motor , defect rectification of vacuum pump , rewinding of motor , replacement of pump , ejector , chemical cleaning and overhauling of ejector , removal , chemical cleaning and fitting back of nozzle , cleaning / renewal of non return flap , collection tank , chemical cleaning of evac collection tank ( i ) opening of manhole door and checking the h2s level in the tank . ( ii ) ventilation of the tank ( iii ) removal of sewage water from the tank ( iv ) flusing of tank with sea / fresh water ( v ) check for any damage to the tank / connecting nozzles ( vi ) minor cold repair of the tank if any , cleaning and checking of level switch , replacement of level switch , cleaning of manifold piping and instrument valves , cleaning and calibration / setting of vacuum switch , system valves , overhauling of gate valve size dn 65 , renewal of valve spindle / stem size dn 65 , renewal of valve seat ( rubber moulded resilient valve seat ) size dn 65 , overhauling of gate valve size dn 100 , renewal of valve spindle / stem size dn 100 , renewal of valve seat ( rubber moulded resilient valve seat ) size dn 100 , overhauling of motorised valve size dn 65 , replacement of valve , control panel , overhauling of complete control panel , defect rectification of control panel , checking of interface with stp , evac vacuum toilet system onlineflex type ( ins makar ) , vacuum pump , complete overhauling of pump ( onlineflex pump ) , complete overhauling of motor , defect recrification of vacuum pump , rewindong of motor , replacement of pump , system valves , overhauling of ball valve , overhauling of non return valve , renewal of valve , cleaning of vacuum manifold piping and instrument valves , cleaning of catcher unit , control panel , defect rectification of control panel ( excluding plc ) , replacement and programming of plc , overhauling of complete control panel , evac vacuum toilet system , vacuum interface valves and vacuum piping ( ins aditya , ins makar , ins suvarna & ins subhadra ) , vacuum toilet , complete overhauling of vacuum toilet , defect rectification of vacuum toilet , repair / renewal of toilet foundation ( fabrication work ) , replacement of vacuum toilet , vacuum interface valve , complete overhauling of vacuum interface valve , defect rectification of vacuum interface valve , repair / renewal of vacuum interface valve foundation , renewal of vacuum interface valve , vacuum interface valve ( scupper type ) , complete overhauling of vacuum interface valve , defect rectification of vacuum interface valve , vacuum piping , repair of vacuum connection ( deck piece ) , renewal of deck piece ( fabrication work ) , chemical cleaning of vacuum piping by removal of piping , mechanical and chemical cleaning of piping , pressure / vacuum testing of piping and fittment ( per mtr ) , renewal of vacuum piping ( ms schedule 40 ) excluding piping material ( per mtr ) , identification of vacuum leakage in system , vacuum generator trials , testing and trials of the vacuum generator in manual and auto mode , part 2 sewage treatment plant sewage treatment plant orca ii a 165 with chlorine generator ( ins makar ) , treatment tank , chemical cleaning of tank ( i ) opening of tank cover and checking the h2s level in the tank . ( ii ) ventilation of the tank ( iii ) removal of sewage water from the tank . ( iv ) flushing of tank with sea / fresh water ( v ) check for any damage to the tank / connecting nozzles ( vi ) minor cold repair of the tank if any , internal coating of tank , cleaning and checking of lever switch , replacement of level switch , cleaning and checking of internal components like spray nozzles , screen , cleaning of sacrificial anode , renewal of sacrificial anode , sedimentation tanks , chemical cleaning of tank ( i ) opening of tank cover and checking the h2s level in the tank . ( ii ) ventilation of the tank ( iii ) removal of sewage water from the tank . ( iv ) flushing of tank with sea / fresh water ( v ) check for any damage to the tank / connecting nozzles ( vi ) minor cold repair of the tank if any , internal coating of tank , cleaning and checking of float valve , replacement of float valve , system valves , cleaning / renewal of ball valves / flow control valve , overhauling of solenoid valve , cleaning and overhauling of stp discharge valve , replacement of stp discharge valve , sea water pump , sludge pump , flow pump and discharge pump , complete overhauling of pump , complete overhauling of motor , defect rectification of pump , replacement of pump , rewinding of motor , dosing pump , complete overhauling of pump , defect rectification of pump , replacement of pump , sewage treatment plant orca ii a 165 with chlorine generator ( ins makar ) , stp control panel , check and clean the electrical components and switches , repair of control panel , replacement of plc , overhauling of complete control panel , chlorine generator , overhauling / defect rectification of chlorine generator , chlorine generator control panel , repair of control panel , overhauling of complete control panel , stp system piping , chemical cleaning of stp piping ( internal piping within stp ) , stp trials , testing and trials of the stp in manual and auto mode , evac sewage treatment plant type orca iii ( ins aditya and ins suvarna ) , sedimentation tank , chemical cleaning of tank ( i ) opening of tank cover and checking the h2s level in the tank . ( ii ) ventilation of the tank ( iii ) removal of sewage water from the tank . ( iv ) flushing of tank with sea / fresh water ( v ) check for any damage to the tank / connecting nozzles ( vi ) minor cold repair of the tank if any , internal coating of tank , cleaning and checking of minim skimmer , cleaning and checking of lamella plates , oxidising tank , chemical cleaning of tank ( i ) opening of tank cover and checking the h2s level in the tank . ( ii ) ventilation of the tank ( iii ) removal of sewage water from the tank . ( iv ) flushing of tank with sea / fresh water ( v ) check for any damage to the tank / connecting nozzles ( vi ) minor cold repair of the tank if any , internal coating of tank , cleaning and checking of level switch , replacement of level switch , evac sewage treatment plant type orca iii ( ins aditya and ins suvarna ) , system valves , cleaning of ball valves , replacement of pvc ball valve , defect rectification of electro pneumatic valve , overhauling of electro pneumatic valve , replacement of electro pneumatic valve , defect rectification of solenoid valve , overhauling of solenoid valve , replacement of solenoid valve , cleaning of ss ball valves , replacement of ss ball valves , system components , cleaning of brushaway filter , renewal of brushaway filter , overhauling of brushaway filter , cleaning of static mixer , renewal of static mixer , checking of sacrificial anode , renewal of sacrificial anode , cleaning of non return valve , replacement of non return valve , cleaning / renewal of hypochlorite chemical tank , sea water pump , recirculation / discharge pump , macerator pump and sludge pump , complete overhauling of pump , complete overhauling of motor , defect rectification of pump , replacement of pump , rewinding of motor , hypochlorite dosing pump and floculant dosing pump , complete overhauling of pump , defect rectification of pump , replacement of pump , stp control panel , c...

National Institute Of Mental Health And Neuro Sciences - Karnataka

23033661 upgradation of existing 0.25 mld stp 1. ksrb 2.2.2: earthwork excavation by manual means for foundation of buildings, water supply, sanitary lines and electrical conduits etc either in pits or in trenches 1.5m and above in width, in hard soil not exceeding 1.5m in depth including dressing the bottom and sides of pits and trenches, stacking the excavated soil clear from edges of excavation with lead upto 50 m including breaking of clods complete as per specifications.in hard soil.no. kbs 2.1 (b) / 2.3.5, 2. ksrb 2.2.4: excavation 1.5m and above in width in soft rock without blasting for foundation of buildings, water supply, sanitary lines and electrical conduits either in pits or in trenches not exceeding 1.5m in depth, stacking the excavated stuff from edges of excavation with lead upto 50m including cost of explosives, labour and hom of equipment complete as per specifications. specification no. kbs 2.1c / 2.9.4 / 2.18 / 2.19, 3. ksrb 2.2.6: excavation for foundation of buildings, water supply and sanitary lines and electrical conduits etc either in pits or in trenches 1.50 m and above in width in hard rock by chiselling and/or wedging, where blasting is prohibited not exceeding 1.50m depth including stacking the excavated stuff clear from the edges of excavation with lead upto 50m including cost labour hom of equipment complete as per specifications., 4. ksrb 3.2: providing and injecting chemical emulsion for pre constructional anti termite treatment, creating continuous chemical barrier under and around the column pits, walls, trenches, basement excavation, top surface of the plinth filling, junction of wall and floor, along the external perimeter of building, expansion joints, over the top surface of consolidated earth on which apron is to be laid, surrounding of pipes and conduits, with chloropyriphos emulsifiable concentrates of 20% concentration at 3.19 litre/sqm., including cost of chemical, diluting in water to one percent concentration, labour, hom complete as per specification. (plinth area of the building at ground floor only shall be measured) specification no. kbs 3.2.6 / 3.2.7, 5. ksrb 2.3: filling available excavated earth (excluding rock) in sides of foundations upto plinth in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with lead upto 50m and lift upto 1.5m including cost of all labour complete as per specifications. specification no. kbs 2.9, 6. ksrb 4.1.3: providing and laying in position plain cement concrete of mix 1:4:8 with opc @ 180 kgs, with 40mm and down size graded granite metal coarse aggregates @ 0.85cum and fine aggregates @ 0.57cum machine mixed,machine mixed concrete laid in layers not exceeding 15cms thick, well compacted, in foundation including cost of all materials, labour, hom , curing complete as per specifications. specification no. kbs 4.1.4.2 for, 7. providing and laying cement concrete using 20mm and down size granite coarse aggregates and fine aggregates of ready mixed concrete for rcc works laid in 15cm thick layers and well compacted, including vibrating,curing etc for all super structure works with all lead and lfit etc complete . (exculsive of cost of steel and fabrication charges) ready mixed cement concrete m 30, 8. ksrb 4.9.2: providing t m t steel reinforcement for rcc work including straightening, cutting, bending, hooking, placing in position, lapping and / or welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary complete as per design (laps, hooks and wastage shall not be measured and paid) cost of materials, labour, hom complete as per specifications. specification no. kbs 4.6.3 for tmt bars fe 500, 9. ksrb 4.6.1: providing and removing centering, shuttering, strutting, propping etc., and removal of form work for foundations, footings, bases of columns for mass concrete including cost of all materials, labour complete as per specifications. specification no. kbs 4.6.2., 10. ksrb 4.6.5: providing and removing centering, shuttering, strutting, propping etc and removal of form work for columns, pillars, , post and struts square/rectangular/polygon in plan including cost of all materials, labour complete as per specifications. specification no. kbs 4.6.2, 11. ksrb 4.6.4: providing and removing centering, shuttering, strutting, propping etc., and removal of form work for vertical surface such as walls at any thickness, including attached pilasters, buttresses, plinth cills and string courses cost of all materials, labour complete as per specifications. specification no. kbs 4.6.2, 12. ksrb 4.6.3: providing and removing centering, shuttering, strutting, propping etc., and removal of form work for flat surface such as suspended floors, roofs, landings, balconies and likes, thickness above 200mm including cost of all materials, labour complete as per specifications. specification no. kbs 4.6.2, 13. ksrb 4.6.11: providing and removing centering, shuttering, strutting, propping etc., and removal of form work for stairs (excluding landing) except spiral staircase including cost of all materials, labour complete as per specification. specification no. kbs 4.6.2., 14. ksrb 5.14: providing and constructig load bearing wall with solid concrete blocks having block density not less 1800 kg/m3 having minimum avarage compressve strength of 4.00 n/mm2 confirming to is 2185(part 1) :2005 and constructed with cm 1:4, as per is 2572:2005 including cost of materials, labour charges, scaffolding, curing, hire charges of machineries etc complete as per specifications. kbs no.5.4 with solid concrete blocks of size 400x150x200mm, 15. ksrb 15.3.11: providing 20mm thick cement plaster in signle coat with cement mortar 1:4, to stone masonry and concrete surface including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications., 16. ksrb 15.3.8: providing 18mm thick cement plaster in signle coat with cement mortar 1:4, to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications., 17. ksrb 15.15.1: providing and applying painting in two coats with plastic emulsion paint of approved brand on wall surface to give an even approved shade after thoroughly brushing the surface, free from mortar drops and other foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour, complete as per specifications. with primer., 18. providing and finishing external walls in two coats over one coat of 100% acrylic silicon glazed primer with antifungal paint for top coat of approved brand and shade to give an even shade after throughly brooming the surface to remove all dirt and loose powdered material, free from mortar drops and other foreign matter cost of materials, labour, complete as per specifications., 19. providing applying two coats of wall putty to inside plastered walls and ceiling using white cement putty. scrapping and levelling the surface using steel blade and preparing the surface even and smooth by using different grade sand papers, including cost of all materials, cost of labour and scaffolding etc., complete as per the specification., 20. providing & fixing of 2 track x 2 panel sliding windows made out of multichambered upvc (matching to ral 9016) sections and with minimum tio2(titanium dioxide) at 6phr with tpv(thermo plastic vulcanized) and lead free, gaskets grey colour having isolated drainage and reinforced with galvanized iron profile through out the window frame. the outer frame having a overall size of 60 mm width x 45mm height with reinforcement of 1mm thickness and sash with overall size of 39mm x 58mm with gi reinforcement of 1mm for the frame and 1.5mm for the sash. glazing bead for fixing of glass shall be of size 20mm x 24mm. windows shall be provided with 5mm plain float glass, standard hardware & single point locking system with touch lock. wall thickness of frame & sash shall be of 2mm 2.5mm. maximum possible size 1819mm x 1819 mm., 21. ksrb 7.3: providing and fixing 1mm thick m.s. sheet garage door with frame and diagonal braces of size 40x40x6mm angle iron, 3.15mm thick m. s. gusset plates at the junctions and corners, with handles, stoppers and locking arrangements etc., including applying a primining coat of red lead paint cost of materials, labour, hom complete as per specifications. double leaf door of size 2.4x2.4m specification no. kbs 7.9/7.12, 22. fabrication, supplying and erecting m.s. tubular trusses of all spans as per approved drawing and design with prefabricated steel applications using quality material and are durable, reliable and corrosion and abrasion resistant. welding shall confirm to latest structural welding code. quality shall be on various parameters like shape, size, design gauge and polish. the entire trusses is anchored in rcc column by using 4 nos. of m.s. anchor bolts at each support with 10mm thick base plate and shoe plate. the work includes cutting, straightening, placing in position of m.s pipes and welding wherever necessary and applying one coat of red oxide primer coat to all the members including cost of all materials, labour charges, and hire charges of machineries for cutting, welding, grinding and erection equipments, with all lead and lift, transportation, etc., complete as per specification., 23. providing and fixing 12.5mm to 25mm expanded metal work of 14 gauge with mathi or nandi wood patties of 50mmx12mm size, including two coats approved paint etc., complete. (including cost of screws) including cost of materials ,lobour ,hom complete as per specifications ., 24. providing trapezoidal profiled sheet; providing and installing of pre painted galvolume iron trapezoidal profiled sheet of approved make 1060 mm width (1000 mm cover width), 28 30 mm crest height with crest distance of 200 mm c/c with 2 ribs at the centre for stiffening. the total coated thickness (tct) of the sheet will be 0.47mm +/ 0.02 mm tolerance zinc alu alloy coating az 150 gsm as per astm 1397/a755 550 mpa steel grade ,5 7 microns epoxy primer on both side of the sheet and polyester top coat 20 22 microns using self drilling/self tapping screws of 25 mm length to be fixed over the existing purlins,rafters,channels and trusses, 25. ksrb 10.3: provding and laying integral cement based waterproofing treatment including preparation of surface as required for treatment of roofs, balconies terraces etc., consisting of following application. (a) applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water proofing compound conforming to is 2645 over the rcc slab after cleaning the surface before treatment. (b) laying cement concrete using broken brick bats 25mm to 100mm size with 50% of cement mortar 1:5 admixed with proprietary water proofing compound conforming is2645 over 20mm thick layer of cement mortar 1:5 admixed with proprietary water proofing compound to required slope and treating similarly the adjoining walls upto 300mm height including rounding off junctions of walls and slabs. (c) after two days of proper curing, applying a second coat of cement slurry admixed with proprietary water proofing compound. (d) finishing the surface with 20mm thick jointless cement mortar of mix 1:4 admixed with proprietary water proofing compound and finally finishing the surface with trowel and neat cement slurry and making of 300x300mm square. (e) the whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test including cost of materials, labour complete as per specifications., 26. providing and fixing ms hand railing for balcony/staircase etc with 50mm dia. m s hollow pipe of 14 gauge, welded to 20mmx20mm m s square rod placed vertically, spaced at 100mm at regular intervals of 600mm. these vertical rods laterally tied to 3 horizontal rods spaced at equal interval. these assembly is fixed to concrete by using expansion bolts and welding the same to reinforcement bars and making good the surface. all the joints and sections hold be cut to length, welded and grinded wherever necessary etc., complete. the work includes cost of all materials, labour charges for all items of work, hire charges for welding, cutting and grinding equipment, and electricity charges, etc., complete as per specification and drawing., 27. supplying and fixing m.s. rectangular poles made out of 2 equal angles of 65 x 65 x 6 mm welded together and fixed in cc (1:2:4) with 2 nos. 16mm dia m.s. hold fast rods each of length 25 cms. including cost of all materials cutting, bending scaffolding wherever necessary, nicely finishing the welded joints with all lead and lifts and as per the directions of the engineer in charge of the work and including providing 2 coats of approved quality paint over one coat of shop painting. (excluding cost of earth work and concrete) .including cost of materials ,labour,hom complete as per specifications, 28. providing and fixing m.s. block pipe of 38mm dia, of heavy guage of 14 including removing the bends, cutting the pipe, and fixing pipe in between the existing two verticle poles ( m.s. rectangular poles) and spot welding the chain link with m.s. block pipe including cost of all materials wastage in cutting, and scaffolding wherever necessary with all lead and lift as directed by the engineer in charge of work etc., complete including two coats of approved quality paint over one coat of shop paint..including cost of materials ,labour,hom complete as per specifications, 29. providing chain link fencing 50 mm size of 8 quage properly stretched between existing rectangular poles and fixed with suitable bolts and nuts, the free ends shall be welded to the pole and block pipe at top and bottom as required including cost of all materials, labour, lead and lifts and as per direction of the engineer in charge of work including two coats of approved quality paint over one coat of shop paint. .including cost of materials ,labour,hom complete as per specifications, 30. shifting of debris with loading, unloading ,transporation charges for 20.0 km with all lead and lift as per direction of the engineer in charge of work, 31. ss bar screen : supplying, fabricating,& fixing made out of ss304 grade, with flats 20x 6mm spaced at 14mm c/c with ss304 rake with gi class ‘b’ pipe handle, size: 500mm x 1500mm x 3500 mm, placed at 45 degree to the vertical in the bar screen chamber in the groove formed out of ss304 angle of size 40 x 6 mm (top,bottom & sides) including cutting, welding, bending wherever necessary finished with matt / shining etc.,complete. cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 32. equalization tank pumps : make: grundfos/ jhoson/ ebara/ cnp/ kirloskar/ equivalent: supplying, installing, testing & commissioning of raw effluent pumps vertical submersible, cutter type, self priming ci body impeller: cast iron/grey iron/a 48 coupled to 7.5 hp, three phase electrical motor, ip 68, class f insulation,earthing for motors complete.provided with 1 no. ms pump header, 1no. flap type ms nrv including necessary fittings like pvc braded hose, ss clamp, gi hose adaptor,elbow etc.complete. cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works. cap: 60 cu m/hr at 15 mts head, end connections 80mm x 80mm., 33. coarse bubble diffusers : supplying, installing, testing & commissioning of coarse bubble diffusers heavy duty pvc pipe (10 kg/cm2) with central tee, yoke, adaptor and end caps including nylon rope, braided hose of required length with all accessories like clamps, nipples etc., to make it retrievable type.size: 90 dia x 1000mm long each. cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 34. fine pore diffusers : supplying, installing, testing & commissioning of fine bubble diffusers heavy duty pvc pipe (10 kg/cm2) with epdm membrane, central tee, yoke, adaptor and end caps including nylon rope, braided hose of required length with all accessories like clamps, nipples etc., to make it retrievable type.size: 90 dia x 1000mm long. cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 35. air blowers (everest /kay/ tmvt/ equivalent) : supplying, installing, testing & commissioning of air blowers 1200 cum/hr at 4500 mmwc rotary twin/tri lobe design type casing: cast iron grade 25.impeller: is 210 grade fg 260 comprising of common base frame with suction / discharge silencers filters, nrv, safety valves, pulley belt guard, pressure gauge etc. provided with ms header, flap type nrv etc., motor: kirloskar / abb / cg /bbl make 40 hp/1500 rpm, three phase. foot mounted.ip 55, class f insulation.cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 36. sludge pumps: grundfos/ jhoson/ ebara/ kirloskar/ equivalent : supplying, installing, testing & commissioning of sludge pumps pump casing: cast iron impeller: cast iron mechanical seal cover:cast iron mechanical seal material: carbon to ceramic self priming, non clog, ci body/ impeller, centrifugal pump coupled to adequate hp motor, mounted on a common ms base frame epoxy painted with necessary bolts, nuts and with manifold.earthing for motors complete. provided with 1 no. ms pump header, ms tail piece, 2nos. butterfly valve including necessary fittings like upvc flange, valve, pipe, pvc elbow etc. cap – 20 cum/ hr @ 15 mtr head motor with kirloskar/ abb/ cg / bbl make foot mounted, 3 hp/2900 rpm, end connections 50mm x 50mm. solid size handling 35 to 40 mm. three phase ip 55, class f insulation.cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 37. decanter mechanism : supplying, installing, testing & commissioning of fully automatic motorized decant valve and accessories, 38. filter press : supplying, installing, testing & commissioning of filter press. polypropylene filter plates of size 800mm x 800mm, 20 numbers with filtration area 9.88 sq meter, cake holding capacity :146.3 litres and operating pressure : 7 bar screw pump for filter press: supplying, installing, testing & commissioning of screw pump for filter press, capacity: 3 4 m3/hr at 7 bar pressure with 3 hp,1450 rpm motor, ms base frame, v pulley belt drive. casing: cast iron, rotor: alloy steel hcp, stator: nitrile, pump speed: 350 rpm. cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 39. filter feed pumps grundfos/ jhoson/ ebara/ kirloskar/ equivalent: supplying, installing, testing & commissioning of filter feed pumps self priming, monobloc, non clog, ci body/ impeller, centrifugal pump coupled to adequate hp motor, mounted on a common ms base frame epoxy painted with necessary bolts, nuts and with manifold.earthing for motors complete. provided with 1 no. ms pump header, ms tail piece, 2 nos. butterfly valve including necessary fittings like upvc flange, valve, pipe, pvc elbow etc.cap – 100 cum/ hr @ 35 mtr head, motor with kirloskar/ abb/ cg/ bbl make foot mounted, 20 hp/2900 rpm, end connections 100mm x 80mm.three phase. ip 55, class f insulation.cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 40. pressure sand filter : supplying, installing, testing & commissioning of pressure sand filter of ms fabricated, shell thickness: 6mm dish thickness: 6 mm and painted internally with two coats of epoxy black and externally with one coat of redoxide primer and above that a layer of two coats of enamel paint. filtering media: graded gravel/sand. working pressure: 3.5 kg/cm2 & testing pressure: 5 kg/cm2 . minimum depth of media: 1000mm & minimum depth of sand: 600mm the filter is fitted with top inlet distribution and bottom collection system. pressure gauge is provided at inlet and outlet. complete set of valves, pressure guage, frontal piping at inlet, outlet backwash and drain out point etc., with ms class ‘b’ pipes (make: jindal) flow 10m3/m2/hr. dia: 2000 mm, hos – 1200 mm, th – 2200mm cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 41. activated carbon filter : supplying, installing, testing & commissioning of activated carbon filter ms fabricated, shell thickness: 6mm dish thickness: 6mm and painted internally with two coats of epoxy black and externally with one coat of red oxide primer and above that a layer of two coats of enamel paint. filtering media: greanular activated carbon. iodine absorption 900 mg/g, apparent density 410 kg/m3. working pressure: 3.5 kg/cm2 & testing pressure: 5 kg/cm2 the filter is fitted with top inlet distribution and bottom collection system. pressure gauge is provided at inlet and outlet. complete set of valves, pressure guage, frontal piping at inlet, outlet backwash and drain out point etc., with ms class ‘b’ pipes (make: jindal/tata/ equivalent) flow 10m3/m2/hr dia: 2000mm, hos – 1200mm, th – 2200mm cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works, 42. uf feed pumps grundfos/ jhoson/ ebara/ kirloskar/ equivalent: supplying, installing, testing & commissioning of filter feed pumps self priming, non clog, ci body/ impeller, centrifugal pump coupled to adequate hp motor, mounted on a common ms base frame epoxy painted with necessary bolts, nuts and with manifold.earthing for motors complete. provided with 1 no. ms pump header, ms tail piece, 2 nos. butterfly valve including necessary fittings like upvc flange, valve, pipe, pvc elbow etc. cap – 60 cum/ hr @ 25 mtr head, motor with kirloskar/abb/cg make foot mounted, 18 hp/2900 rpm, end connections 80mm x 80mm.three phase. ip 55, class f insulation.cost of material and conveyance of all materials, labour for all item of work, hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 43. ultra filtration unit: supplying, installing,complete automizing, testing & commissioning of uf unit with hollow fiber type structure, 45 m2/unit membrane filtration area, ph range 2 to 10, reinforced abs and pvc housing, pore size 0.025 micrometer. material of construction membrane pvdf, pesm, maximum operating pressure 4 bar, 44. ultra filtration backwash pump grundfos/ jhoson/ ebara/ kirloskar/ equivalent: supplying, installing, automizing, testing & commissioning of ultra filtration feed pumps self priming, non clog, ci body/ impeller, centrifugal pump coupled to adequate hp motor, mounted on a common ms base frame epoxy painted with necessary bolts, nuts and with manifold. earthing for motors complete. provided with 1 no. ms pump header, ms tail piece, 2 nos. butterfly valve including necessary fittings like upvc flange, valve, pipe, pvc elbow etc. cap – 100 cum/ hr @ 20 mtr head, motor with kirloskar/abb/cg make foot mounted, 5 hp/2900 rpm, three phase. ip 55, class f insulation. cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all ther incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 45. ionic oxidation unit (standard make): supplying, installing, testing & commissioning of ionic oxidation unit. process involves in situ generation of reactive oxygen species for removal of organic matter and to disinfect, with a hydrodynamic range of 30 cum/hr to 50 cum/hr, fac production 150 g/cum to 250g/cum. supplying, commissioning of suitable pump to the disinfection unit.dc power source: supplying ,installation of dc regulated power supply unit of type igbt based switch mode power supply with forced air cooled, ip 32 protection over voltage, over current, single phase, over temperature. input power 3 phase supply, output volatge 0 60 dc, rated current 0 100 adc, independently variable, constant power source, output ripple less than 1 percent. al powder coated rack to accommodate power supplies, polarity reversal unit along with filters and fans. cost of material and conveyance of all materials, labour for all item of work, hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge, 46. clear/ garden water pumps: jhoson/ ebara/ kirloskar/ equivalent: supplying, installing, testing & commissioning of booster pumps self priming, non clog, ci body/ impeller, centrifugal pump coupled to adequate hp motor, mounted on a common ms base frame epoxy painted with necessary bolts, nuts and with manifold. purpose is to pump the treated water to the storage tank located behind the quatrus earthing for motors complete. provided with 1 no. ms pump header, ms tail piece, 2 nos. butterfly valve including necessary fittings like upvc flange, valve, pipe, pvc elbow etc. cap 60 cum/ hr @ 100 mtr head, motor with kirloskar/abb/cg make foot mounted, 7.5 hp/2900 rpm, three phase. ip 55, class f insulation.cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 47. in plant piping: supplying, installing, testing & commissioning of all plant piping shall be in ms class ‘b’, epoxy painted & designed for following velocities & of tata / jindal make. pressure rating : cpvc 10 kg/cm2, ms 15 kg/cm2 all valves (butterfly valves, gate valves, non return valves, etc.) shall be of ci, b/f type with ss flaps/seal, lever operated matching ms flanges & ss304 through bolts, audco make.cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc.,, 48. in plant electricals and plc automation : supplying, installing, testing & commissioning of plant electricals and plc panel non compartmentalized design floor mounted, dust and vermin proof design, to degree of ip 54 as per is 13947, phosphated and powder coated with siemens grey color. the panel will have voltmeter, ammeter, energy meter and indicating lamps for the pumps on outgoing side to indicate the operation mode. powerwiring: al armored cable, with gi ladder type cable tray.cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc.,the in plant electricals include, 1.1kv grade xlpe insulated and pvc sheathed aluminium conductor armoured standard power cables confirming to is 7098of sizes, 2 core 4 sqmm, 2 core 10 sqmm, 3 core 4 sqmm, 3 core 25 sqmm, 4 core 10 sqmm along with respective sizes aluminium lugs. also perforated cable trayincluding vertical and horizontal bends, reducers, tees, cross members and other accessories. point wiring with modular switches and sockets, concealed conduit wiring for primary light point with 1.5 sqmm, 1.1kv grade single core wire., 49. o & m of commissioned stp for the period of 1 year including 3 shift operation, supervision, consumables, chemicals and necessary spares required for maintenance and including analysis of raw sewage & treated water., 50. supplying, fixing and wiring earth electrode for grounding of sophis ticated medical equipments, lifts, transformers, dg sets etc using 40mm dia 2.9 mm thick 2.5 meter long gi pipe with gi funnel with mesh and suitable size reducer fixed on the top of the earth electrode. the funnel should be enclosed in a cc chamber of 600x600x600mm with a cast iron cover. the earth electrode shall have staggered holes of 12mm dia and the electrode should be covered 600mm around with alternate layers of salt and charcoal from the bottom of the cc chamber. the connection from the electrode is to be established through gi strip using gi bolts and nuts and the work should be carried out as per the instruction of the engineer in charge, 51. supplying and running of gi/copper strips for grounding connections using necessary fixing materials as required for 25x3mm copper strip, 52. supplying and fixing (600x600x6) mm copper plate in existing gi pipe with copper bolt and nuts, 53. supplying of 1.1 kv lt ug cable xlpe or heat resistant pvc insulated, pvc extruded inner sheath armoured ug lt cable as per is 1554 (part 1) or is 7098 part 1, armouring strip thickness in average +5% and resistivity 14 ohms/kms (max) as per is 3975 for 3.5 core 240 sqmm, 54. labour charges for laying of 1.1 kv class ug cable in existing trench gi pipe / stoneware pipe / on wall / on pole as required.in existing trench/duct. for 185 sqmm to 240 sqmm, 55. digging of trench of 0.6m deep x 0.50 mtr wide refiling the trench to the required ground level and consolidating etc., complete.(as per civil sr ksrb i 2, p 7) for asphalt cutting, 56. providing and filling sand in excavated trench to cover already laid ug cable to a depth of 150mm all round the cable., 57. concealed conduit system;supplying heavy gauge pvc conduit pipe 19/20 mm dia 2 mm thick confirming to is 2509 with suitable size bends,metal/pvc junction boxes, adhesive paste etc., and running before concreting the slab.the conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using pvc end enclosures ,run with 18 swg gi fish wire wherever necessary., 58. concealed conduit system; supplying heavy gauge pvc conduit pipe 25 mm dia 2 mm thick confirming to is 2509 with suitable size bends, metal/pvc junction boxes, adhesive paste etc., and running before concreting the slab. the conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using pvc end enclosures ,run with 18 swg gi fish wire wherever necessary., 59. supplying and fixing metal fan box with round hook, 60. point wiring using copper wire without switch. supplying and wiring adopting loop system in existing pvc conduit /casing capping casing capping using 2 x 1.5 sqmm (phase & neutral) & 1 x 1.0 sqmm (earth wire) frls multi strand pvc insulated copper wire (confirming to is 694 latest amendments ) without control switch shall be fixed on existing plastic sheet/gang box the other end of the wires shall be terminated with sufficient loose length in a wood/pvc round block. complete for each outlet, for short point upto 3 mtr from tapping point to out let via switch box, 61. point wiring using copper wire without switch. supplying and wiring adopting loop system in existing pvc conduit /casing capping casing capping using 2 x 1.5 sqmm (phase & neutral) & 1 x 1.0 sqmm (earth wire) frls multi strand pvc insulated copper wire (confirming to is 694 latest amendments ) without control switch shall be fixed on existing plastic sheet/gang box the other end of the wires shall be terminated with sufficient loose length in a wood/pvc round block. complete for each outlet, for medium point above 3 mtr upto 6 mtr from tapping point to out let via switch box, 62. point wiring using copper wire without switch. supplying and wiring adopting loop system in existing pvc conduit /casing capping casing capping using 2 x 1.5 sqmm (phase & neutral) & 1 x 1.0 sqmm (earth wire) frls multi strand pvc insulated copper wire (confirming to is 694 latest amendments ) without control switch shall be fixed on existing plastic sheet/gang box the other end of the wires shall be terminated with sufficient loose length in a wood/pvc round block. complete for each outlet, for long point above 6 mtr upto 10 mtr from tapping point to out let via switch box, 63. wiring for lighting /power circuit using one of frls pvc insulated 1100 v grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified is 694:confirming to latest amendments. for 2.5 sqmm, 64. wiring for lighting /power circuit using one of frls pvc insulated 1100 v grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified is 694:confirming to latest amendments. for 4 sqmm, 65. supplying and flush mounting powder coated/galvanized metal box suitable for mounting modular switch plates. the box should be firmly flush mounted after due groove cutting in brick/stone/cc wall for 16 18 way, 66. supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/pvc box. for 16 18 module, 67. supplying and fixing of modular switch and connected accessories on existing modular switch plate as per is 3854 and is 1293 for 6 amps one way switch, 68. supplying and fixing of modular switch and connected accessories on existing modular switch plate as per is 3854 and is 1293 for 6 amps 3 way socket, 69. supplying and fixing of modular switch and connected accessories on existing modular switch plate as per is 3854 and is 1293 for 32 amps d p switch, 70. supplying and fixing of modular switch and connected accessories on existing modular switch plate as per is 3854 and is 1293 for 6 /16 amps universal socket, ...

National Institute Of Mental Health And Neuro Sciences - Karnataka

22808856 construction (upgradation of existing 0.25 mld stp) and supply, installation, testing and commission 1. ksrb 2.2.2: earthwork excavation by manual means for foundation of buildings, water supply, sanitary lines and electrical conduits etc either in pits or in trenches 1.5m and above in width, in hard soil not exceeding 1.5m in depth including dressing the bottom and sides of pits and trenches, stacking the excavated soil clear from edges of excavation with lead upto 50 m including breaking of clods complete as per specifications.in hard soil.no. kbs 2.1 (b) / 2.3.5, 2. ksrb 2.2.4: excavation 1.5m and above in width in soft rock without blasting for foundation of buildings, water supply, sanitary lines and electrical conduits either in pits or in trenches not exceeding 1.5m in depth, stacking the excavated stuff from edges of excavation with lead upto 50m including cost of explosives, labour and hom of equipment complete as per specifications. specification no. kbs 2.1c / 2.9.4 / 2.18 / 2.19, 3. ksrb 2.2.6: excavation for foundation of buildings, water supply and sanitary lines and electrical conduits etc either in pits or in trenches 1.50 m and above in width in hard rock by chiselling and/or wedging, where blasting is prohibited not exceeding 1.50m depth including stacking the excavated stuff clear from the edges of excavation with lead upto 50m including cost labour hom of equipment complete as per specifications., 4. ksrb 3.2: providing and injecting chemical emulsion for pre constructional anti termite treatment, creating continuous chemical barrier under and around the column pits, walls, trenches, basement excavation, top surface of the plinth filling, junction of wall and floor, along the external perimeter of building, expansion joints, over the top surface of consolidated earth on which apron is to be laid, surrounding of pipes and conduits, with chloropyriphos emulsifiable concentrates of 20% concentration at 3.19 litre/sqm., including cost of chemical, diluting in water to one percent concentration, labour, hom complete as per specification. (plinth area of the building at ground floor only shall be measured) specification no. kbs 3.2.6 / 3.2.7, 5. ksrb 2.3: filling available excavated earth (excluding rock) in sides of foundations upto plinth in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with lead upto 50m and lift upto 1.5m including cost of all labour complete as per specifications. specification no. kbs 2.9, 6. ksrb 4.1.3: providing and laying in position plain cement concrete of mix 1:4:8 with opc @ 180 kgs, with 40mm and down size graded granite metal coarse aggregates @ 0.85cum and fine aggregates @ 0.57cum machine mixed,machine mixed concrete laid in layers not exceeding 15cms thick, well compacted, in foundation including cost of all materials, labour, hom , curing complete as per specifications. specification no. kbs 4.1.4.2 for, 7. providing and laying cement concrete using 20mm and down size granite coarse aggregates and fine aggregates of ready mixed concrete for rcc works laid in 15cm thick layers and well compacted, including vibrating,curing etc for all super structure works with all lead and lfit etc complete . (exculsive of cost of steel and fabrication charges) ready mixed cement concrete m 30, 8. ksrb 4.9.2: providing t m t steel reinforcement for rcc work including straightening, cutting, bending, hooking, placing in position, lapping and / or welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary complete as per design (laps, hooks and wastage shall not be measured and paid) cost of materials, labour, hom complete as per specifications. specification no. kbs 4.6.3 for tmt bars fe 500, 9. ksrb 4.6.1: providing and removing centering, shuttering, strutting, propping etc., and removal of form work for foundations, footings, bases of columns for mass concrete including cost of all materials, labour complete as per specifications. specification no. kbs 4.6.2., 10. ksrb 4.6.5: providing and removing centering, shuttering, strutting, propping etc and removal of form work for columns, pillars, , post and struts square/rectangular/polygon in plan including cost of all materials, labour complete as per specifications. specification no. kbs 4.6.2, 11. ksrb 4.6.4: providing and removing centering, shuttering, strutting, propping etc., and removal of form work for vertical surface such as walls at any thickness, including attached pilasters, buttresses, plinth cills and string courses cost of all materials, labour complete as per specifications. specification no. kbs 4.6.2, 12. ksrb 4.6.3: providing and removing centering, shuttering, strutting, propping etc., and removal of form work for flat surface such as suspended floors, roofs, landings, balconies and likes, thickness above 200mm including cost of all materials, labour complete as per specifications. specification no. kbs 4.6.2, 13. ksrb 4.6.11: providing and removing centering, shuttering, strutting, propping etc., and removal of form work for stairs (excluding landing) except spiral staircase including cost of all materials, labour complete as per specification. specification no. kbs 4.6.2., 14. ksrb 5.14: providing and constructig load bearing wall with solid concrete blocks having block density not less 1800 kg/m3 having minimum avarage compressve strength of 4.00 n/mm2 confirming to is 2185(part 1) :2005 and constructed with cm 1:4, as per is 2572:2005 including cost of materials, labour charges, scaffolding, curing, hire charges of machineries etc complete as per specifications. kbs no.5.4 with solid concrete blocks of size 400x150x200mm, 15. ksrb 15.3.11: providing 20mm thick cement plaster in signle coat with cement mortar 1:4, to stone masonry and concrete surface including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications., 16. ksrb 15.3.8: providing 18mm thick cement plaster in signle coat with cement mortar 1:4, to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications., 17. ksrb 15.15.1: providing and applying painting in two coats with plastic emulsion paint of approved brand on wall surface to give an even approved shade after thoroughly brushing the surface, free from mortar drops and other foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour, complete as per specifications. with primer., 18. providing and finishing external walls in two coats over one coat of 100% acrylic silicon glazed primer with antifungal paint for top coat of approved brand and shade to give an even shade after throughly brooming the surface to remove all dirt and loose powdered material, free from mortar drops and other foreign matter cost of materials, labour, complete as per specifications., 19. providing applying two coats of wall putty to inside plastered walls and ceiling using white cement putty. scrapping and levelling the surface using steel blade and preparing the surface even and smooth by using different grade sand papers, including cost of all materials, cost of labour and scaffolding etc., complete as per the specification., 20. providing & fixing of 2 track x 2 panel sliding windows made out of multichambered upvc (matching to ral 9016) sections and with minimum tio2(titanium dioxide) at 6phr with tpv(thermo plastic vulcanized) and lead free, gaskets grey colour having isolated drainage and reinforced with galvanized iron profile through out the window frame. the outer frame having a overall size of 60 mm width x 45mm height with reinforcement of 1mm thickness and sash with overall size of 39mm x 58mm with gi reinforcement of 1mm for the frame and 1.5mm for the sash. glazing bead for fixing of glass shall be of size 20mm x 24mm. windows shall be provided with 5mm plain float glass, standard hardware & single point locking system with touch lock. wall thickness of frame & sash shall be of 2mm 2.5mm. maximum possible size 1819mm x 1819 mm., 21. ksrb 7.3: providing and fixing 1mm thick m.s. sheet garage door with frame and diagonal braces of size 40x40x6mm angle iron, 3.15mm thick m. s. gusset plates at the junctions and corners, with handles, stoppers and locking arrangements etc., including applying a primining coat of red lead paint cost of materials, labour, hom complete as per specifications. double leaf door of size 2.4x2.4m specification no. kbs 7.9/7.12, 22. fabrication, supplying and erecting m.s. tubular trusses of all spans as per approved drawing and design with prefabricated steel applications using quality material and are durable, reliable and corrosion and abrasion resistant. welding shall confirm to latest structural welding code. quality shall be on various parameters like shape, size, design gauge and polish. the entire trusses is anchored in rcc column by using 4 nos. of m.s. anchor bolts at each support with 10mm thick base plate and shoe plate. the work includes cutting, straightening, placing in position of m.s pipes and welding wherever necessary and applying one coat of red oxide primer coat to all the members including cost of all materials, labour charges, and hire charges of machineries for cutting, welding, grinding and erection equipments, with all lead and lift, transportation, etc., complete as per specification., 23. providing and fixing 12.5mm to 25mm expanded metal work of 14 gauge with mathi or nandi wood patties of 50mmx12mm size, including two coats approved paint etc., complete. (including cost of screws) including cost of materials ,lobour ,hom complete as per specifications ., 24. providing trapezoidal profiled sheet; providing and installing of pre painted galvolume iron trapezoidal profiled sheet of approved make 1060 mm width (1000 mm cover width), 28 30 mm crest height with crest distance of 200 mm c/c with 2 ribs at the centre for stiffening. the total coated thickness (tct) of the sheet will be 0.47mm +/ 0.02 mm tolerance zinc alu alloy coating az 150 gsm as per astm 1397/a755 550 mpa steel grade ,5 7 microns epoxy primer on both side of the sheet and polyester top coat 20 22 microns using self drilling/self tapping screws of 25 mm length to be fixed over the existing purlins,rafters,channels and trusses, 25. ksrb 10.3: provding and laying integral cement based waterproofing treatment including preparation of surface as required for treatment of roofs, balconies terraces etc., consisting of following application. (a) applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water proofing compound conforming to is 2645 over the rcc slab after cleaning the surface before treatment. (b) laying cement concrete using broken brick bats 25mm to 100mm size with 50% of cement mortar 1:5 admixed with proprietary water proofing compound conforming is2645 over 20mm thick layer of cement mortar 1:5 admixed with proprietary water proofing compound to required slope and treating similarly the adjoining walls upto 300mm height including rounding off junctions of walls and slabs. (c) after two days of proper curing, applying a second coat of cement slurry admixed with proprietary water proofing compound. (d) finishing the surface with 20mm thick jointless cement mortar of mix 1:4 admixed with proprietary water proofing compound and finally finishing the surface with trowel and neat cement slurry and making of 300x300mm square. (e) the whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test including cost of materials, labour complete as per specifications., 26. providing and fixing ms hand railing for balcony/staircase etc with 50mm dia. m s hollow pipe of 14 gauge, welded to 20mmx20mm m s square rod placed vertically, spaced at 100mm at regular intervals of 600mm. these vertical rods laterally tied to 3 horizontal rods spaced at equal interval. these assembly is fixed to concrete by using expansion bolts and welding the same to reinforcement bars and making good the surface. all the joints and sections hold be cut to length, welded and grinded wherever necessary etc., complete. the work includes cost of all materials, labour charges for all items of work, hire charges for welding, cutting and grinding equipment, and electricity charges, etc., complete as per specification and drawing., 27. supplying and fixing m.s. rectangular poles made out of 2 equal angles of 65 x 65 x 6 mm welded together and fixed in cc (1:2:4) with 2 nos. 16mm dia m.s. hold fast rods each of length 25 cms. including cost of all materials cutting, bending scaffolding wherever necessary, nicely finishing the welded joints with all lead and lifts and as per the directions of the engineer in charge of the work and including providing 2 coats of approved quality paint over one coat of shop painting. (excluding cost of earth work and concrete) .including cost of materials ,labour,hom complete as per specifications, 28. providing and fixing m.s. block pipe of 38mm dia, of heavy guage of 14 including removing the bends, cutting the pipe, and fixing pipe in between the existing two verticle poles ( m.s. rectangular poles) and spot welding the chain link with m.s. block pipe including cost of all materials wastage in cutting, and scaffolding wherever necessary with all lead and lift as directed by the engineer in charge of work etc., complete including two coats of approved quality paint over one coat of shop paint..including cost of materials ,labour,hom complete as per specifications, 29. providing chain link fencing 50 mm size of 8 quage properly stretched between existing rectangular poles and fixed with suitable bolts and nuts, the free ends shall be welded to the pole and block pipe at top and bottom as required including cost of all materials, labour, lead and lifts and as per direction of the engineer in charge of work including two coats of approved quality paint over one coat of shop paint. .including cost of materials ,labour,hom complete as per specifications, 30. shifting of debris with loading, unloading ,transporation charges for 20.0 km with all lead and lift as per direction of the engineer in charge of work, 31. ss bar screen : supplying, fabricating,& fixing made out of ss304 grade, with flats 20x 6mm spaced at 14mm c/c with ss304 rake with gi class ‘b’ pipe handle, size: 500mm x 1500mm x 3500 mm, placed at 45 degree to the vertical in the bar screen chamber in the groove formed out of ss304 angle of size 40 x 6 mm (top,bottom & sides) including cutting, welding, bending wherever necessary finished with matt / shining etc.,complete. cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 32. equalization tank pumps : make: grundfos/ jhoson/ ebara/ cnp/ kirloskar/ equivalent: supplying, installing, testing & commissioning of raw effluent pumps vertical submersible, cutter type, self priming ci body impeller: cast iron/grey iron/a 48 coupled to 7.5 hp, three phase electrical motor, ip 68, class f insulation,earthing for motors complete.provided with 1 no. ms pump header, 1no. flap type ms nrv including necessary fittings like pvc braded hose, ss clamp, gi hose adaptor,elbow etc.complete. cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works. cap: 60 cu m/hr at 15 mts head, end connections 80mm x 80mm., 33. coarse bubble diffusers : supplying, installing, testing & commissioning of coarse bubble diffusers heavy duty pvc pipe (10 kg/cm2) with central tee, yoke, adaptor and end caps including nylon rope, braided hose of required length with all accessories like clamps, nipples etc., to make it retrievable type.size: 90 dia x 1000mm long each. cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 34. fine pore diffusers : supplying, installing, testing & commissioning of fine bubble diffusers heavy duty pvc pipe (10 kg/cm2) with epdm membrane, central tee, yoke, adaptor and end caps including nylon rope, braided hose of required length with all accessories like clamps, nipples etc., to make it retrievable type.size: 90 dia x 1000mm long. cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 35. air blowers (everest /kay/ tmvt/ equivalent) : supplying, installing, testing & commissioning of air blowers 1200 cum/hr at 4500 mmwc rotary twin/tri lobe design type casing: cast iron grade 25.impeller: is 210 grade fg 260 comprising of common base frame with suction / discharge silencers filters, nrv, safety valves, pulley belt guard, pressure gauge etc. provided with ms header, flap type nrv etc., motor: kirloskar / abb / cg /bbl make 40 hp/1500 rpm, three phase. foot mounted.ip 55, class f insulation.cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 36. sludge pumps: grundfos/ jhoson/ ebara/ kirloskar/ equivalent : supplying, installing, testing & commissioning of sludge pumps pump casing: cast iron impeller: cast iron mechanical seal cover:cast iron mechanical seal material: carbon to ceramic self priming, non clog, ci body/ impeller, centrifugal pump coupled to adequate hp motor, mounted on a common ms base frame epoxy painted with necessary bolts, nuts and with manifold.earthing for motors complete. provided with 1 no. ms pump header, ms tail piece, 2nos. butterfly valve including necessary fittings like upvc flange, valve, pipe, pvc elbow etc. cap – 20 cum/ hr @ 15 mtr head motor with kirloskar/ abb/ cg / bbl make foot mounted, 3 hp/2900 rpm, end connections 50mm x 50mm. solid size handling 35 to 40 mm. three phase ip 55, class f insulation.cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 37. decanter mechanism : supplying, installing, testing & commissioning of fully automatic motorized decant valve and accessories, 38. filter press : supplying, installing, testing & commissioning of filter press. polypropylene filter plates of size 800mm x 800mm, 20 numbers with filtration area 9.88 sq meter, cake holding capacity :146.3 litres and operating pressure : 7 bar screw pump for filter press: supplying, installing, testing & commissioning of screw pump for filter press, capacity: 3 4 m3/hr at 7 bar pressure with 3 hp,1450 rpm motor, ms base frame, v pulley belt drive. casing: cast iron, rotor: alloy steel hcp, stator: nitrile, pump speed: 350 rpm. cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 39. filter feed pumps grundfos/ jhoson/ ebara/ kirloskar/ equivalent: supplying, installing, testing & commissioning of filter feed pumps self priming, monobloc, non clog, ci body/ impeller, centrifugal pump coupled to adequate hp motor, mounted on a common ms base frame epoxy painted with necessary bolts, nuts and with manifold.earthing for motors complete. provided with 1 no. ms pump header, ms tail piece, 2 nos. butterfly valve including necessary fittings like upvc flange, valve, pipe, pvc elbow etc.cap – 100 cum/ hr @ 35 mtr head, motor with kirloskar/ abb/ cg/ bbl make foot mounted, 20 hp/2900 rpm, end connections 100mm x 80mm.three phase. ip 55, class f insulation.cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 40. pressure sand filter : supplying, installing, testing & commissioning of pressure sand filter of ms fabricated, shell thickness: 6mm dish thickness: 6 mm and painted internally with two coats of epoxy black and externally with one coat of redoxide primer and above that a layer of two coats of enamel paint. filtering media: graded gravel/sand. working pressure: 3.5 kg/cm2 & testing pressure: 5 kg/cm2 . minimum depth of media: 1000mm & minimum depth of sand: 600mm the filter is fitted with top inlet distribution and bottom collection system. pressure gauge is provided at inlet and outlet. complete set of valves, pressure guage, frontal piping at inlet, outlet backwash and drain out point etc., with ms class ‘b’ pipes (make: jindal) flow 10m3/m2/hr. dia: 2000 mm, hos – 1200 mm, th – 2200mm cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 41. activated carbon filter : supplying, installing, testing & commissioning of activated carbon filter ms fabricated, shell thickness: 6mm dish thickness: 6mm and painted internally with two coats of epoxy black and externally with one coat of red oxide primer and above that a layer of two coats of enamel paint. filtering media: greanular activated carbon. iodine absorption 900 mg/g, apparent density 410 kg/m3. working pressure: 3.5 kg/cm2 & testing pressure: 5 kg/cm2 the filter is fitted with top inlet distribution and bottom collection system. pressure gauge is provided at inlet and outlet. complete set of valves, pressure guage, frontal piping at inlet, outlet backwash and drain out point etc., with ms class ‘b’ pipes (make: jindal/tata/ equivalent) flow 10m3/m2/hr dia: 2000mm, hos – 1200mm, th – 2200mm cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works, 42. uf feed pumps grundfos/ jhoson/ ebara/ kirloskar/ equivalent: supplying, installing, testing & commissioning of filter feed pumps self priming, non clog, ci body/ impeller, centrifugal pump coupled to adequate hp motor, mounted on a common ms base frame epoxy painted with necessary bolts, nuts and with manifold.earthing for motors complete. provided with 1 no. ms pump header, ms tail piece, 2 nos. butterfly valve including necessary fittings like upvc flange, valve, pipe, pvc elbow etc. cap – 60 cum/ hr @ 25 mtr head, motor with kirloskar/abb/cg make foot mounted, 18 hp/2900 rpm, end connections 80mm x 80mm.three phase. ip 55, class f insulation.cost of material and conveyance of all materials, labour for all item of work, hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 43. ultra filtration unit: supplying, installing,complete automizing, testing & commissioning of uf unit with hollow fiber type structure, 45 m2/unit membrane filtration area, ph range 2 to 10, reinforced abs and pvc housing, pore size 0.025 micrometer. material of construction membrane pvdf, pesm, maximum operating pressure 4 bar, 44. ultra filtration backwash pump grundfos/ jhoson/ ebara/ kirloskar/ equivalent: supplying, installing, automizing, testing & commissioning of ultra filtration feed pumps self priming, non clog, ci body/ impeller, centrifugal pump coupled to adequate hp motor, mounted on a common ms base frame epoxy painted with necessary bolts, nuts and with manifold. earthing for motors complete. provided with 1 no. ms pump header, ms tail piece, 2 nos. butterfly valve including necessary fittings like upvc flange, valve, pipe, pvc elbow etc. cap – 100 cum/ hr @ 20 mtr head, motor with kirloskar/abb/cg make foot mounted, 5 hp/2900 rpm, three phase. ip 55, class f insulation. cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all ther incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 45. ionic oxidation unit (standard make): supplying, installing, testing & commissioning of ionic oxidation unit. process involves in situ generation of reactive oxygen species for removal of organic matter and to disinfect, with a hydrodynamic range of 30 cum/hr to 50 cum/hr, fac production 150 g/cum to 250g/cum. supplying, commissioning of suitable pump to the disinfection unit.dc power source: supplying ,installation of dc regulated power supply unit of type igbt based switch mode power supply with forced air cooled, ip 32 protection over voltage, over current, single phase, over temperature. input power 3 phase supply, output volatge 0 60 dc, rated current 0 100 adc, independently variable, constant power source, output ripple less than 1 percent. al powder coated rack to accommodate power supplies, polarity reversal unit along with filters and fans. cost of material and conveyance of all materials, labour for all item of work, hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge, 46. clear/ garden water pumps: jhoson/ ebara/ kirloskar/ equivalent: supplying, installing, testing & commissioning of booster pumps self priming, non clog, ci body/ impeller, centrifugal pump coupled to adequate hp motor, mounted on a common ms base frame epoxy painted with necessary bolts, nuts and with manifold. purpose is to pump the treated water to the storage tank located behind the quatrus earthing for motors complete. provided with 1 no. ms pump header, ms tail piece, 2 nos. butterfly valve including necessary fittings like upvc flange, valve, pipe, pvc elbow etc. cap 60 cum/ hr @ 100 mtr head, motor with kirloskar/abb/cg make foot mounted, 7.5 hp/2900 rpm, three phase. ip 55, class f insulation.cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 47. in plant piping: supplying, installing, testing & commissioning of all plant piping shall be in ms class ‘b’, epoxy painted & designed for following velocities & of tata / jindal make. pressure rating : cpvc 10 kg/cm2, ms 15 kg/cm2 all valves (butterfly valves, gate valves, non return valves, etc.) shall be of ci, b/f type with ss flaps/seal, lever operated matching ms flanges & ss304 through bolts, audco make.cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc.,, 48. in plant electricals and plc automation : supplying, installing, testing & commissioning of plant electricals and plc panel non compartmentalized design floor mounted, dust and vermin proof design, to degree of ip 54 as per is 13947, phosphated and powder coated with siemens grey color. the panel will have voltmeter, ammeter, energy meter and indicating lamps for the pumps on outgoing side to indicate the operation mode. powerwiring: al armored cable, with gi ladder type cable tray.cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc.,the in plant electricals include, 1.1kv grade xlpe insulated and pvc sheathed aluminium conductor armoured standard power cables confirming to is 7098of sizes, 2 core 4 sqmm, 2 core 10 sqmm, 3 core 4 sqmm, 3 core 25 sqmm, 4 core 10 sqmm along with respective sizes aluminium lugs. also perforated cable trayincluding vertical and horizontal bends, reducers, tees, cross members and other accessories. point wiring with modular switches and sockets, concealed conduit wiring for primary light point with 1.5 sqmm, 1.1kv grade single core wire., 49. o & m of commissioned stp for the period of 1 year including 3 shift operation, supervision, consumables, chemicals and necessary spares required for maintenance and including analysis of raw sewage & treated water., 50. supplying, fixing and wiring earth electrode for grounding of sophis ticated medical equipments, lifts, transformers, dg sets etc using 40mm dia 2.9 mm thick 2.5 meter long gi pipe with gi funnel with mesh and suitable size reducer fixed on the top of the earth electrode. the funnel should be enclosed in a cc chamber of 600x600x600mm with a cast iron cover. the earth electrode shall have staggered holes of 12mm dia and the electrode should be covered 600mm around with alternate layers of salt and charcoal from the bottom of the cc chamber. the connection from the electrode is to be established through gi strip using gi bolts and nuts and the work should be carried out as per the instruction of the engineer in charge, 51. supplying and running of gi/copper strips for grounding connections using necessary fixing materials as required for 25x3mm copper strip, 52. supplying and fixing (600x600x6) mm copper plate in existing gi pipe with copper bolt and nuts, 53. supplying of 1.1 kv lt ug cable xlpe or heat resistant pvc insulated, pvc extruded inner sheath armoured ug lt cable as per is 1554 (part 1) or is 7098 part 1, armouring strip thickness in average +5% and resistivity 14 ohms/kms (max) as per is 3975 for 3.5 core 240 sqmm, 54. labour charges for laying of 1.1 kv class ug cable in existing trench gi pipe / stoneware pipe / on wall / on pole as required.in existing trench/duct. for 185 sqmm to 240 sqmm, 55. digging of trench of 0.6m deep x 0.50 mtr wide refiling the trench to the required ground level and consolidating etc., complete.(as per civil sr ksrb i 2, p 7) for asphalt cutting, 56. providing and filling sand in excavated trench to cover already laid ug cable to a depth of 150mm all round the cable., 57. concealed conduit system;supplying heavy gauge pvc conduit pipe 19/20 mm dia 2 mm thick confirming to is 2509 with suitable size bends,metal/pvc junction boxes, adhesive paste etc., and running before concreting the slab.the conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using pvc end enclosures ,run with 18 swg gi fish wire wherever necessary., 58. concealed conduit system; supplying heavy gauge pvc conduit pipe 25 mm dia 2 mm thick confirming to is 2509 with suitable size bends, metal/pvc junction boxes, adhesive paste etc., and running before concreting the slab. the conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using pvc end enclosures ,run with 18 swg gi fish wire wherever necessary., 59. supplying and fixing metal fan box with round hook, 60. point wiring using copper wire without switch. supplying and wiring adopting loop system in existing pvc conduit /casing capping casing capping using 2 x 1.5 sqmm (phase & neutral) & 1 x 1.0 sqmm (earth wire) frls multi strand pvc insulated copper wire (confirming to is 694 latest amendments ) without control switch shall be fixed on existing plastic sheet/gang box the other end of the wires shall be terminated with sufficient loose length in a wood/pvc round block. complete for each outlet, for short point upto 3 mtr from tapping point to out let via switch box, 61. point wiring using copper wire without switch. supplying and wiring adopting loop system in existing pvc conduit /casing capping casing capping using 2 x 1.5 sqmm (phase & neutral) & 1 x 1.0 sqmm (earth wire) frls multi strand pvc insulated copper wire (confirming to is 694 latest amendments ) without control switch shall be fixed on existing plastic sheet/gang box the other end of the wires shall be terminated with sufficient loose length in a wood/pvc round block. complete for each outlet, for medium point above 3 mtr upto 6 mtr from tapping point to out let via switch box, 62. point wiring using copper wire without switch. supplying and wiring adopting loop system in existing pvc conduit /casing capping casing capping using 2 x 1.5 sqmm (phase & neutral) & 1 x 1.0 sqmm (earth wire) frls multi strand pvc insulated copper wire (confirming to is 694 latest amendments ) without control switch shall be fixed on existing plastic sheet/gang box the other end of the wires shall be terminated with sufficient loose length in a wood/pvc round block. complete for each outlet, for long point above 6 mtr upto 10 mtr from tapping point to out let via switch box, 63. wiring for lighting /power circuit using one of frls pvc insulated 1100 v grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified is 694:confirming to latest amendments. for 2.5 sqmm, 64. wiring for lighting /power circuit using one of frls pvc insulated 1100 v grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified is 694:confirming to latest amendments. for 4 sqmm, 65. supplying and flush mounting powder coated/galvanized metal box suitable for mounting modular switch plates. the box should be firmly flush mounted after due groove cutting in brick/stone/cc wall for 16 18 way, 66. supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/pvc box. for 16 18 module, 67. supplying and fixing of modular switch and connected accessories on existing modular switch plate as per is 3854 and is 1293 for 6 amps one way switch, 68. supplying and fixing of modular switch and connected accessories on existing modular switch plate as per is 3854 and is 1293 for 6 amps 3 way socket, 69. supplying and fixing of modular switch and connected accessories on existing modular switch plate as per is 3854 and is 1293 for 32 amps d p switch, 70. supplying and fixing of modular switch and connected accessories on existing modular switch plate as per is 3854 and is 1293 for 6 /16 amps universal socket, ...

National Institute Of Mental Health And Neuro Sciences - Karnataka

22553580 construction (upgradation of existing 0.25 mld stp) and supply, installation, testing and commissioning of electro mechanical equipments to 1.20 mld sewage treatment plant at nimahns campus 1. ksrb 2.2.2: earthwork excavation by manual means for foundation of buildings, water supply, sanitary lines and electrical conduits either in pits or in trenches 1.5m and above in width, in hard soil not exceeding 1.5m in depth including dressing the bottom and sides of pits and trenches, stacking the excavated soil clear from edges of excavation with lead upto 50m after breaking of clods complete as per specifications. specification no. kbs 2.1 (b)/2.3.5(p.5/2.4), 2. ksrb 3.2: providing and injecting chemical emulsion for pre constructional anti termite treatment, creating continuous chemical barrier under and around the column pits, walls, trenches, basement excavation, top surface of the plinth filling, junction of wall and floor, along the external perimeter of building, expansion joints, over the top surface of consolidated earth on which apron is to be laid, surrounding of pipes and conduits, with chloropyriphos emulsifiable concentrates of 20% concentration, including cost of chemical, diluting in water to one percent concentration, labour, hom of equipments, complete as per specification. (plinth area of the building at ground floor only shall be measured) specification no. kbs 3.2.6/3.2.7 (p.9/3.2), 3. ksrb 4.1.3: providing and laying in position plain cement concrete of mix m 1:4:8 with opc cement @ 180 kgs, with 40mm and down size graded granite metal coarse aggregates @ 0.85cum and fine aggregates @ 0.57cum machine mixed,machine mixed concrete laid in layers not exceeding 15cms thick, well compacted, in foundation including cost of all materials, labour, hom of machinery, curing complete as per specifications. specification no. kbs 4.1.4.2 (p.12/4.3), 4. ksrb 4.6.4: providing and removing centering, shuttering, strutting, propping etc., and removal of form work for vertical surface such as walls at any thickness, including attached pilasters, buttresses, plinth cills and string courses cost of all materials, labour complete as per specifications. specification no. kbs 4.6.2 (p.15/4.31), 5. ksrb 4.6.2: providing and removing centering, shuttering, strutting, propping etc., and removal of form work for flat surface such as roofs, landings, balconies and likes, thickness upto 200mm including cost of all materials, labour complete as per specifications up to 3.50 m from ground level. specification no. kbs 4.6.2 (p.15/4.18), 6. ksrb 4.6.10: providing and removing centering, shuttering, strutting, propping etc., for chajjas, corbels etc., including edges including cost of all materials, labour complete as per specifications. specification no. kbs 4.6.2 (p.16/4.37), 7. ksrb 4.6.8: providing and removing centering, shuttering, strutting, propping etc., and removal of form work for sides and soffits of beams, beam haunchings, cantilever girders, bressumers and lintels not exceeding 1 m in depth including cost of all materials, labour complete as per specifications. specification no. kbs 4.6.2 (p.16/4.35), 8. ksrb 4.2.1: providing and laying in position reinforced cement concrete of design mix m25 with opc cement @ 340 kgs, with 20mm and down size graded granite metal coarse aggregates @ 0.70 cum and fine aggregates @ 0.47cum, with superplasticiser @ 3 ltrs confirming to is 9103 1999 reafirmed 2008, machine mixed, concrete laid in layers not excceding 15 cms thick, vibrated for all works in foundation for footings, pedestals, retaining walls, return walls, walls (any thickness) including attached plasters, column pillars, posts, struts, buttresses, bed blocks, anchor blocks & plinths etc., including cost of all materials, labour, hom of machinery, curing, complete as per specifications. specification no. kbs 4.1.4.6 (p.13/4.10), 9. ksrb 4.2.11: providing and laying in position reinforced cement concrete of design mix m20 with opc cement @ 27.20 kgs, with 12mm and down size graded granite metal coarse aggregates @ 0.05865cum and fine aggregates @ 0.0391cum, with superplastisiser @ 0.225 ltrs., machine mixed, well compacted for plain chajja of 8.5 cms. average thickness, upto ground floor level, including cost of all materials, labour, hom of machinery, curing, complete as per specifications. specification no. kbs 4.1.4.6 (p.14/4.20), 10. ksrb 4.9.2: providing tmt steel reinforcement for rcc work including straightening, cutting, bending, hooking, placing in position, lapping and/or welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary complete as per design (laps, hooks and wastage shall not be measured and paid) cost of materials, labour, hom of machinery complete as per specifications. specification no. kbs 4.6.3 for tmt bars fe 500 (p.17/4.46.2), 11. ksrb 6.2.4: providing and constructing burnt brick masonry with approved quality of non modular bricks of standard size of class designation 5.0 newton per sqmm with cement mortar 1:4 for basement and superstructure including cost of materials, labour charges, scaffolding, curing complete as per specification. specification no. kbs 6.2 (p.27/6.7), 12. ksrb 5.2.3: providing and constructing granite/trap/basalt size stone masonry in foundation with cement mortar 1:6, stone hammerd dressed in course not less than 20 cms high, bond stones at two m. apart in each course including cost of materials, labour, curing complete as per specifications. kbs 5.1.13 (p.23/5.6), 13. ksrb 7.9: providing and fixing ms grill work for windows and ventilators using ms flats, or ms square rods, or combination of ms flats and square rods as per approved design, drawing including cutting steel sections and welding the same to required pattern with a coat of red lead primer, cost of materials, fixtures, labour and hom of machinery complete as per specificaitons. specification no. kbs 7.12 (p.32/7.9), 14. ksrb 7.10: providing and fixing in position aluminium windows and ventilators as per approved drawings with sliding shutters using double track window frame section o f size 61.85x31.75mm with 1.2mm thcik, bottom section weight 0.695 kg/m, sides and top sections 1.3 mm thick weight 0.659 kg/m: and shutter comprising top and bottom section of size 40mmx18mm, 1.25mm thick 0.417 kg/m: shutter outer side 40mmx18mm, 1.25mm thick weight 0.417 kg/m, shutter interlock section 40mmx26.7mm, 1.1mm thick, weight 0.469 kg/m the shutters mounted on nylon rollers with approved quality of fixtures such as aluminium handles tower bolts etc., and providing and fixing 5.5mm thick plain glass for shutters fitted with rubber beading aluminium sections including cutting to required length, joints mitred subdividing the frame tenonned and rivetted in the assembled frame stiffened with end clips at corners angles etc., and fixed to the walls, lintels, floor beams/cills as the case may be with necessary steel screws, raul plugs, or teak wood gatties including cutting masonry or concrete and making good the original surface using cement mortar, aluminium sections pretreated for removal of any specification no. kbs do using aluminium section powdered coated to a minimum of 60 70 microns with exterior durable pure polyester grade powder of approved quality. (p.33/7.10.2), 15. ksrb 15.3.8: providing 18mm thick cement plaster in signle coat with cement mortar 1:4, to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications. (p.113/15.16), 16. ksrb 15.15.1: providing and applying painting in two coats with plastic emulsion paint of approved brand on wall surface to give an even approved shade after thoroughly brushing the surface, free from mortar drops and other foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour, complete as per specifications. with primer (p.117/15.51.2), 17. providing applying two coats of wall putty to inside plastered walls and ceiling using white cement putty. scrapping and levelling the surface using steel blade and preparing the surface even and smooth by using different grade sand papers, including cost of all materials, cost of labour and scaffolding etc., complete as per the specification.(p.126/15.106), 18. ksrb 15.7: providing lime rendering for plastering to wall and ceiling, including cost of materials, labour, curing complete as per specifications. (p. 115/15.33), 19. ksrb 15.18.2: providing and applying enamel metal paint two coats (excluding priming coat) over new steel or other metal surface brushing to give an even shade after cleaning oil, grease, dirt and other foreign matter, including cost of materials, labour, complete as per specifications.(p.121/15.74), 20. providing and finishing external walls in two coats over one coat of 100% acrylic silicon glazed primer with antifungal paint for top coat of approved brand and shade to give an even shade after throughly brooming the surface to remove all dirt and loose powdered material, free from mortar drops and other foreign matter cost of materials, labour, complete as per specifications. (p.125/15.104), 21. ksrb 4.1.5: providing and laying in position plain cement concrete of mix m20 with opc cement @ 300 kgs, with 20mm and down size graded granite metal coarse aggregates @ 0.69cum and fine aggregates @ 0.43cum machine mixed, concrete laid in layers not exceeding 15 cms thick, well compacted, in foundation, plinth, and cills including cost of all materials, labour, hom of machinery, curing complete as per specifications. specification no. kbs 4.1.4.2 (p.12/4.5), 22. ksrb 2.4: refilling available earth around pipe lines, cables in layers not exceeding 20cms in depth, compacting each deposited layer by ramming after watering with lead upto 50m and lift upto 1.5m including cost of all labour complete as per specifications.(p.6/2.11) supplying and fixing m.s. rectangular poles made out of 2 equal angles of 65x65x6 mm welded together and fixed in cc (1:2:4) with 2 nos. 16mm dia m.s. hold fast rods each of length 25 cms. including cost of all materials cutting, bending scaffolding wherever necessary, nicely finishing the welded joints with all lead and lifts and as per the directions of the engineer in charge of the work and including providing 2 coats of approved quality paint over one coat of shop painting. (excluding cost of earth work and concrete) ( p. 262/37.2), 23. supplying and fixing m.s. rectangular poles made out of 2 equal angles of 65x65x6 mm welded together and fixed in cc (1:2:4) with 2 nos. 16mm dia m.s. hold fast rods each of length 25 cms. including cost of all materials cutting, bending scaffolding wherever necessary, nicely finishing the welded joints with all lead and lifts and as per the directions of the engineer in charge of the work and including providing 2 coats of approved quality paint over one coat of shop painting. (excluding cost of earth work and concrete) ( p. 262/37.2), 24. providing and fixing m.s. block pipe of 38mm dia, of heavy guage of 14 including removing the bends, cutting the pipe, and fixing pipe in between the two verticle poles (m.s. rectangular poles) and spot welding the chain link with m.s. block pipe including cost of all materials wastage in cutting, and scaffolding wherever necessary with all lead and lift as directed by the engineer in charge of work etc., complete including two coats of approved quality paint over one coat of shop paint. ( p.262/37.4), 25. providing chain link fencing 50 mm size of 8 quage properly stretched between rectangular poles and fixed with suitable bolts and nuts, the free ends shall be welded to the pole and block pipe at top and bottom as required including cost of all materials, labour, lead and lifts and as per direction of the engineer in charge of work including two coats of approved quality paint over one coat of shop paint. ( p. 262/37.3), 26. shifting of debris with loading, unloading ,transporation charges for 1.0 km with all lead and lift as per direction of the engineer in charge of work (p140), 27. ksrb 4.4.1: extra for use of water proofing compound in cement concrete of mix m 1:1:2, at one kg of compound pr bag of cement. specification no. kbs (p.14/4.24), 28. ksrb 15.4.4:extra for providing and mixing waterproofing compound in cement plaster work at one kg per bag or in the proportion recommended by the manufacturers, for cement mortat 1:4, 18mm thick cost of materials complete as per specifications.(p.113/15.26), 29. providing and applying composite water proofing compound as impregnate only on wet surfaces to arrest leaks in surfaces to arrest leakes in surfaces such as roof cealing, internal and external walls, flooring and other surfaces apart from water tanks, sumps, reservoirs, by mixing the composite water proofing compound with water in ratio of 1:10 to make a workable slurry and pouring it on all cleaned and prepared corners and disturbed area and further mixing in the ratio 1:20 and pouring it on the prepared surface by cleaning the surface with etchant chemical from dirt foreign materials etc., and allowing it to be there upto 3 hours and then cleaning the same using water complete as per specification so that the surface is go back and ready to use after 4hours.(p.67/10.8), 30. fabricating, supplying & erecting ms angular truss for all spans as per approved designs and drawing. the entire truss is anchored suitably by using 4 nos. of m.s anchor bolts at each support, with base plate and shoe plate. the work includes cutting, straightening, placing in position of m.s angle and welding wherever necessary, and applying one coat of red oxide primer coat to all the members including cost of all materials, labour charges, and hire charges of machineries for cutting, welding, grinding and erection equipments, etc., complete as per specification (p41/7.30), 31. ksrb 13.8.9: providing and fixing to wall, ceiling and floor high density polyethylene pipes 6.00kgf/sq cm working pressure 110 mm outside diameter raising mains and exposed distribution pipes with special flange, compression type fittings,wall clips,making good the wall,ceiling and floor including cost of all materials,labour charges,hom of equipments and testing complete as per specifications specification no.kbs 13.2.15.2/13.9 (p 94/13.73.5), 32. ksrb 7.3: providing and fixing 1mm thick ms sheet garage door with frame and diagonal braces of size 40x40x6mm angle iron, 3.15mm thick ms gusset plates at the junctions and corners, with handles, stoppers and locking arrangements etc., including applying a primining coat of red lead paint cost of materials, labour, hom of machinery complete as per specifications. double leaf door of size 2.4x2.4m specification no. kbs 7.9/7.12 (p.31/7.3), 33. ksrb 12.5.2: constructing brick masonry cirular type manhole 0.91 m internal dia at bottom 1.67m deep and 0.56m dia at top with table moulded non modular bricks of 50 class designation 50 in cement mortar 1:4, inside cement plastered 12mm thick with cement mortar 1:3, finished with a floating coat of neat cement, foundation concrete m 10 using 40mm and downsize granite metal and making necessary channel in cement concrete m 50 with 20mm and downsize granite metal finished with a floating coat of neat cement, with s.f.r.c. cover and frame (heavy duty, hd 20 grade designation) 560mm internal diameter confirming is:12592, total weight cover and frame to be not less than 182kg, fixed in cement concrete 1:2:4, 20mm and downsize broken granite metal, providing and removing centering, shuttering including cost of materials, labour charges, hom of mechineries complete as per specifications. (excavation, footrests and 12mm thick cement plaster on the external surface shall be paid seperately) specification no. kbs 12.4 (p.71/11.38), 34. ksrb 12.8.1: constructing brick masonry inspection chamber 455x610mm, and 450mm depth, (clear inside dimension) for single pipeline, using table moulded non modlular bricks of class designation 50 in cement mortar 1:5, c.i cover with frame (light duty) 455x610mm internal dimensions, total weight of cover with frame to be not less than 38kg (weight of cover 23kg and weight of frame 15 kg) r.c.c. top slab with cement concrete m 15 with 20mm and downsize granite metal, foundation concrete m 5 with 40mm and dowsize granite metal inside plastering 12mm thick with cement mortar 1:3, finish smooth with a floating coat of cement on walls and bed concrete complete as per standard design including cost of materials, labour charges, curing complete as per specifications. specifications. no kbs do 600x 600mm, and 450mm depth, (clear inside dimension) for single pipeline, using table moulded non modular bricks of class designation 50 in cement mortar 1:5, c.i. cover with frame (light duty) 600x600mm (p.73/11.50.1), 35. providing and fixing to wall, ceiling and floor unplasticised pvc 6.00kgs/sq cm working pressure with pipe fittings,wall clips etc and making good the wall,ceiling and floor for sanitary pipelines including cost of all materials,labour charges,hom of equipments and testing complete as per specifications for 160 mm dia (p88/12.116.3), 36. providing and fixing for flooring 20mm thick gang saw water cut sadarhalli grey granite in cm 1:4 proportion, cut to required shape, pattern with paper joints, finished with cement mortar using white cement and colour pigments to match the colour of slab making through jointing with sealant, groves in joints including cost of curing. do minimum width of 1200 mm (p.109/14.61), 37. providing full nosing for 20mm thick granite slab using required machinery including cost and conveyance of all materials, labour for all items of work, hom of equipment etc., complete as per specification. (p.108/14.55), 38. iso proof sealer providing waterproof treatment to roof slab using 2 coats of acrylic co polymer elastomeric isoproof sealer & protector. the surface shall be prepared free of tar, dust, fungus, loose particles etc., the surface shall be applied with basecoat of crystallization liquid and then isoproof, wetting agent and liquid (1:1:6) over the prepared surface. in addition the surface shall be provided with polysulphide/acrylic sealant to v groves, making haunch at junction of parapet and roof slab and at damaged portion using patching mortar to drain off rain water. over this one coat of flexible cementatious membrane (fcm), spreading 2 layers of 40 gsm non woven geotextile membrane as reinforcing material (over fcm) with one primer coat of isoproof & applying second coat of isoproof liquid over the primer coat conforming to astm d 412 1992. the work shall be carried out as per the directions of the engineer in charge.(p271/38.3), 39. providing and fixing ms hand railing for balcony/staircase etc with 50mm dia. m s hollow pipe of 14 gauge, welded to 20mmx20mm m s square rod placed vertically, spaced at 100mm at regular intervals of 600mm. these vertical rods laterally tied to 3 horizontal rods spaced at equal interval. these assembly is fixed to concrete by using expansion bolts and welding the same to reinforcement bars and making good the surface. all the joints and sections hold be cut to length, welded and grinded wherever necessary etc., complete. the work includes cost of all materials, labour charges for all items of work, hire charges for welding, cutting and grinding equipment, and electricity charges, etc., complete as per specification and drawing. (p.42/7.35), 40. supplying water storage tanks made of virgin polymer (lldpe) with two layers outer black or blue and inner white layer of approved quality and make, conforming to i.s.i./iso/ssi specifications. (p.265/37.58), 41. providing and fixing to wall, ceiling and floor unplasticised pvc 6.00 kgs/sqcm working pressure with pipe fittings, wall clips etc., and making good the wall, ceiling and floor for sanitary pipelines including cost of all materials, labour charges, hom of acquirements and testing complete as per specifications. for 110 mm dia (p.88/12.116.1) providing and fixing chorinated poly venyl chloride (cpvc) pipes conforming to is 15778, having thermal stability for hot and cold water supply including all cpvc plain and brass threaded fittings including fixing the pipe with clamp at 1.00 mtr. spacing. this includes jointing of pipes and fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete. (concealed work including cutting chases and good the walls etc.,) 25mm nominal od pipes (p.93/13.86.3), 42. providing and fixing chorinated poly venyl chloride (cpvc) pipes conforming to is 15778, having thermal stability for hot and cold water supply including all cpvc plain and brass threaded fittings including fixing the pipe with clamp at 1.00 mtr. spacing. this includes jointing of pipes and fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete. (concealed work including cutting chases and good the walls etc.,) 20mm nominal od pipes (p.96/13.86.2), 43. providing and fixing chorinated poly venyl chloride (cpvc) pipes conforming to is 15778, having thermal stability for hot and cold water supply including all cpvc plain and brass threaded fittings including fixing the pipe with clamp at 1.00 mtr. spacing. this includes jointing of pipes and fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete. (concealed work including cutting chases and good the walls etc.,) 20mm nominal od pipes (p.96/13.86.2), 44. geolphysical investigation of site for sinking borewell for supplying water to the habitation either through the hand pump, mws, p.w.s.s by vertical electrical sounding by adopting venner or schlumbergers method, including reconnaissance survey of geological formation, geophysical investigation of existing ground water in the vicinity, its quality, quantity & acceptebility of the users indicating the location of site, recommended depth of casing pipe reqired to seal the top unconsolidated formation including an extra depth of 1.0 meter. in consolidated formation for proper seating of casing pipe, depth of drilling required to cover full depth of aquifer proposed to be tapped, probable yield and other information required including transportation of instrument and accessories to work site, engaging technical personal and labour required etc., (sr pre 2012 13 page.47/9.4), 45. sinking of borewell of 165 mm dia clear using superfast hydraulic rig of capacity 250 psig & above 900 cmf & above in all strata including over burden upto 20 m, fixing of casing pipes, collars and cap with necessary cutting, threading and welding including transportation of rig and supporting vehicle, crew charges and cost of consumables, etc., complete including yield testing at the final depth with a minimum working of compressor for one hour (excluding cost of casing pipes, collars, cap etc) for 0.00 to 50.00 mtrs (sr pre 2012 13 page.46/9.1), 46. sinking of borewell of 165 mm dia clear using superfast hydraulic rig of capacity 250 psig & above 900 cmf & above in all strata including over burden upto 20 m, fixing of casing pipes, collars and cap with necessary cutting, threading and welding including transportation of rig and supporting vehicle, crew charges and cost of consumables, etc., complete including yield testing at the final depth with a minimum working of compressor for one hour (excluding cost of casing pipes, collars, cap etc) for 50.00 to100.00 mtrs (sr pre 2012 13 page.46/9.1), 47. sinking of borewell of 165 mm dia clear using superfast hydraulic rig of capacity 250 psig & above 900 cmf & above in all strata including over burden upto 20 m, fixing of casing pipes, collars and cap with necessary cutting, threading and welding including transportation of rig and supporting vehicle, crew charges and cost of consumables, etc., complete including yield testing at the final depth with a minimum working of compressor for one hour (excluding cost of casing pipes, collars, cap etc) for 100.00 to 150.00 mtrs (sr pre 2012 13 page.46/9.1), 48. sinking of borewell of 165 mm dia clear using superfast hydraulic rig of capacity 250 psig & above 900 cmf & above in all strata including over burden upto 20 m, fixing of casing pipes, collars and cap with necessary cutting, threading and welding including transportation of rig and supporting vehicle, crew charges and cost of consumables, etc., complete including yield testing at the final depth with a minimum working of compressor for one hour (excluding cost of casing pipes, collars, cap etc) for 150.00 to 200.00 mtrs (sr pre 2012 13 page.46/9.1), 49. sinking of borewell of 165 mm dia clear using superfast hydraulic rig of capacity 250 psig & above 900 cmf & above in all strata including over burden upto 20 m, fixing of casing pipes, collars and cap with necessary cutting, threading and welding including transportation of rig and supporting vehicle, crew charges and cost of consumables, etc., complete including yield testing at the final depth with a minimum working of compressor for one hour (excluding cost of casing pipes, collars, cap etc) for 200.00 to 250.00 mtrs (sr pre 2012 13 page.46/9.1), 50. sinking of borewell of 165 mm dia clear using superfast hydraulic rig of capacity 250 psig & above 900 cmf & above in all strata including over burden upto 20 m, fixing of casing pipes, collars and cap with necessary cutting, threading and welding including transportation of rig and supporting vehicle, crew charges and cost of consumables, etc., complete including yield testing at the final depth with a minimum working of compressor for one hour (excluding cost of casing pipes, collars, cap etc) for 250.00 to 300.00 mtrs (sr pre 2012 13 page.46/9.1), 51. sinking of borewell of 165 mm dia clear using superfast hydraulic rig of capacity 250 psig & above 900 cmf & above in all strata including over burden upto 20 m, fixing of casing pipes, collars and cap with necessary cutting, threading and welding including transportation of rig and supporting vehicle, crew charges and cost of consumables, etc., complete including yield testing at the final depth with a minimum working of compressor for one hour (excluding cost of casing pipes, collars, cap etc) for 300.00 to 350.00 mtrs (sr pre 2012 13 page.46/9.1), 52. supply of isi mark 175mm nominal bore. plain end steel casing pipe grade of steel fee 410 of wall thickness 5.4mm thick confirming to is 4270:2001 and latest amendements, electric resistance welded steel tube material and confirming to is 1387/1993 and manfactured by basic open hearth electric or basic oxygen process in random length to 5 to 7 mts. both ends threaded confirming to is 554/1985. one end fixed with socket confirming to is 4270:2001 and the other end with screwed pipes. all pipes shall be reasonably free from defects. the tubes shall be reasonbably free from defects. the tubes shall be reasonably straight should be with isi marketing, weighing 25.10kg/mtr. (inclusive of all taxes and duties). prices include collar medium duty. (sr pre 2012 13 page.iii/84), 53. supply of 175 mm m.s.cap (sr pre 2012 13 page.iii/85), 54. supply of 175 mm m.scollar (sr pre 2012 13 page. iii/86), 55. supply of submersible three phase pump set of 10.0hp/7.5kw,20 stage as per direction of the engineer in charge of the work (brand atalanta, suguna, c.r.i, kirloskar and other equivalent pumps ) (sr pwd 2016 17 page.xxxxii/21), 56. ksrb 13.6.3.6: providing and fixing in position brass gate valve with c.i wheel of approved quality (screwed end) 50 mm nominal bore including cost of all materials, labour and hom of equipments with all leads complete as per specifications. specification. no. kbs 13.2.6/13.3 (p.92/13.37), 57. ksrb 13.7.1.4: providing and fixing in position 50 mm nominal bore gun metal non return valve horizontal type of approved make including cost of all materials, labour and hom of equipments with all leads complete as per specifications. specification no.kbs 13.2.10/13.13 (p.93/13.55), 58. ksrb 13.1.1: providing and fixing to wall, ceiling and floor galvanised/mild steel tube 50 mm dia nominal bore with fittings (medium grade weight 5.24 kg/m) b class including cost of all materials, labour charges, hom of equipments and testing complete as per specifications. specification no. kbs 13.2.14/13.8 (p.90/13.6), 59. supplying and drawing 3 core flat pvc sheathed submersible pump cable manufactured with electrolytic grade copper with flexible copper with low resistance conductor confirmining to table 3 class 5 of is:8130 1984 and virgin grade pvc insulation and powder coating extruded pvc sheathed suitable for working voltage upto 1100volts as per is 694:1990 and confirming to gtp of group a for 3 c x 2.5 sq mm(12/2.10), 60. supplying fully automatic star delta starter unit push button type with suitable wires, 3 contactors, one adjustable thermal timer mounted on a common base plate held in steel enclosure for use on 400/440 volts 3 phase and wired after fixing to the existing wooden board for motor for upto 12.5 hp. (44/6.2.1), 61. supplying and running of gi/copper strips for grounding connections, using necessary fixing materials as required.for gi strip 25mmx3mm (55/7.3.1), 62. supplying and fixing moulded case circuit breaker (mccb) over the existing wood/panel board using necessary screws, bolts, nuts and wiring complete. protection of overload and short circuit with thermal magnetic/ microprocessor release and earth fault as per is 13947. ( icu = ics) three pole ,100 amps 25 ka (46/6.13.1), 63. ss bar screen : supplying, fabricating,& fixing made out of ss304 grade, with flats 20x 6mm spaced at 14mm c/c with ss304 rake with gi class ‘b’ pipe handle,size: 800mm x 800mm x 1500 mm, placed at 45 degree to the vertical in the bar screen chamber in the groove formed out of ss304 angle of size 40 x 6 mm (top,bottom & sides) including cutting, welding, bending wherever necessary finished with matt/shining etc.,complete. cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 64. equalization tank pumps : make: grundfos/ jhoson/ ebara/ kirloskar/ equivalent: supplying, installing, testing & commissioning of raw effluent pumps, cutter type vertical submersible ci body impeller: cast iron/grey iron/a 48 coupled to 5 hp, three phase electrical motor, ip 68, class f insulation,earthing for motors complete.provided with 1 no. ms pump header, 1no. flap type ms nrv including necessary fittings like pvc braded hose, ss clamp, gi hose adaptor,elbow etc.complete. cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works. cap: 15 cu m/hr at 15 mts head, end connections 50mm x 50mm, 65. coarse bubble diffusers : supplying, installing, testing & commissioning of coarse bubble diffusers heavy duty pvc pipe (10 kg/cm2) with central tee, yoke, adaptor and end caps including nylon rope, braided hose of required length with all accessories like clamps, nipples etc., to make it retrievable type.size: 90 dia x 1000mm long each. cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 66. fine pore diffusers : supplying, installing, testing & commissioning of fine bubble diffusers heavy duty pvc pipe (10 kg/cm2) with membrane, central tee, yoke, adaptor and end caps including nylon rope, braided hose of required length with all accessories like clamps, nipples etc., to make it retrievable type.size: 90 dia x 1000mm long. cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 67. air blowers : (everest/key/ equivalent) : supplying, installing, testing & commissioning of air blowers 200 cum/hr at 4500 mmwc rotary twin/tri lobe design type.casing: cast iron grade 25.impeller: is 210 grade fg 260 comprising of common base frame with suction/discharge silencers filters, nrv, safety valves, pulley belt guard, pressure gauge etc. provided with ms header, flap type nrv etc., motor: kirloskar/abb/cg make 5 hp/1300 rpm, three phase. foot mounted.ip 55, class f insulation.cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 68. sludge pumps grundfos/ jhoson/ ebara/ kirloskar/ equivalent : supplying, installing, testing & commissioning of sludge pumps pump casing: cast iron, impeller: cast iron, mechanical seal cover: cast iron, mechanical seal material: carbon to ceramic, self priming, non clog, ci body/ impeller, centrifugal pump coupled to adequate hp motor, mounted on a common ms base frame epoxy painted with necessary bolts, nuts and with manifold.earthing for motors complete. provided with 1 no. ms pump header, ms tail piece, 2nos. butterfly valve including necessary fittings like upvc flange, valve, pipe, pvc elbow etc. cap – 5 cum/ hr @ 20 mtr head motor with kirloskar/abb/cg make foot mounted, 3 hp/2900 rpm, three phase ip 55, class f insulation.cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 69. filter feed pumps grundfos/ jhoson/ ebara/ kirloskar/ equivalent: supplying, installing, testing & commissioning of filter feed pumps self priming, non clog, ci body/ impeller, centrifugal pump coupled to adequate hp motor, mounted on a common ms base frame epoxy painted with necessary bolts, nuts and with manifold. earthing for motors complete. provided with 1 no. ms pump header, ms tail piece, 2 nos. butterfly valve including necessary fittings like upvc flange, valve, pipe, pvc elbow etc. cap – 10 cum/ hr @ 35 mtr head, motor with kirloskar/abb/cg make foot mounted, 5 hp/2900 rpm, three phase. ip 55, class f insulation.cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., 70. pressure sand filter : supplying, installing, testing & commissioning of pressure sand filter ms fabricated, shell thickness: 6mm dish thickness: 6 mm and painted internally with two coats of epoxy black and externally with one coat of redoxide primer and above that a layer of two coats of enamel paint. filtering media: graded gravel/sand. working pressure: 3.5 kg/cm2 & testing pressure: 5 kg/cm2 minimum depth of media: 1000mm &.minimum depth of sand: 600mm the filter is fitted with top inlet distribution and bottom collection system. pressure gauge is provided at inlet and outlet. complete set of valves, pressure guage, frontal piping at inlet, outlet backwash and drain out point etc., with ms class ‘b’ pipes (make: jindal) dia: 900 mm, hos – 1200 mm, th – 2200mm cost of material and conveyance of all materials, labour for all item of work,hom of equipment charges and all other incidental charges etc., complete as per the specification & directions of the engineer in charge of the works., ...

Bharat Electronics Limited - Karnataka

22363226 procurement of modern service garage tools for iaf station, tejpur, and jorhat assam state: supply of manual type tyre bead breaker kit . make: sarv , supply and installation of arc welding machine: arc welding machine 200 amps air cooled , 3 phase , with electrode holder , pair of leather hand gloves , helment with welding glass , incoming copper cable of 20 meters of 4 core x 4 sq . mm ( cable code: yy ) , 2 meters 3 core x 16 sq . mm copper welding cable with lugs , 2 meters 3 core x 16 sq . mm earthing copper cable with heavy duty earth clamp and lugs , wire brush , chipping hammer . make: electroweld weldarc . , supply of installation accessories: consists of 1 ) composite pipe size : 1 { 2025 20x25mm ) 40 mtrs . 2 ) female tee { 2025x1 / 2 } 12 no . 3 ) female elbow { 2025x1 / 2 } 4 no . 4 ) reduced nipple { 2025x1 / 2 } 8 no . 5 ) rounding tools 1 no . 6 ) plastic pipe chamfer 1 no . 7 ) pipe cutter 1 no . 8 ) external spring 1 no . 9 ) internal spring 1 no . 10 ) heavy duty clamp 100nos . set : consisting of screw nail 100 nos . , wooden gatta 1 100 nos . 11 ) flexible pipe 4mtr . long 3 / 8 id with end fitting 1 / 2 female thread 2 mtr 12 ) ball valve 1 / 2 12 no . 13 ) quick coupler 40 sma 16 no . 14 ) quick coupler 40 spa 16 no . 15 ) quick coupler adopter 20 pma 4 no . 16 ) brass hex nipple 1 / 2 x 1 / 2 12 no . 17 ) brass pu hose adopter 1 / 2 x 12mm 4 no . 18 ) brass pu hose adopter 1 / 4 x 12mm 4 no . 19 ) pu tube 8 mm x12 mm 50 mtrs 20 ) pu hose 8 mm x12 mm 15 mtrs . long coiled with end fittings 1 no . 21 ) quick coupler 40 ppa 6 no . 22 ) 1set of fittins for sand blasting machine & tyre inflator 1 no . 23 ) lubricator 1 / 2 1 no . 24 ) air tool lubricant 500ml vg 22 2 no . 25 ) auto drain valve 1 no . 26 ) micro / fine filter 1 no . 27 ) pre filter 1 no . 28 ) weather proof ( ip 67 ) non metallic type 20 a , 2p+e industrial plug & socket with 25 a sp mcb ( 10ka , d , curve ) along with sheet steel enclosure & accessories ( legrand / nine electric / schneider electric / l&t makes ) . 02 nos . 29 ) 16a 3 pin plug top ( anchor / legrand / mk makes ) 06 nos . 30 ) 12 module modular pvc box with modular cover plates , switch plates and accessories ( anchor / legrand / mk makes ) 02 nos . 31 ) 16a modular switch ( anchor / legrand / mk makes ) 06 nos . 32 ) 5 / 15a 5 pin modular socket ( anchor / legrand / mk makes ) 06 nos . 33 ) modular blanking plates 05 nos . 34 ) 4 . 0 sq . mm ring type cu lugs 16 nos . 35 ) insulation tapes ( red / yellow / blue / black / green ) 02 rolls of each colour . , supply and installation of electrically driven submersible sludge pump of capacity 1 hp , single phase , class f insulation , ip 68 protection , with minimum 10 meters head , stainless steel pump body , ss shaft , automatic on off , float switch , over load protection , non return valve , 1 1 / 2 inch nylon hose pipe of 30 meters for pump discharge with clamps , screws , tapes , installation accessories , 10 meters of 3 core x 2 . 5 sq . mm copper cable for inlet power connection to pump , 5 meters nylon rope . make: kirloskar , supply and installation of fuel trnsfr pmp , 12vdc , mieco mdl dyb 40dc , with inlet pipe nylon of 2 mtrs with fixing clamp , outlet pipe nylon of 5 mtrs with clamp , fuel gun , battery connecting wire of 5 mtrs with clips , clamping accessories , tape , clamps , screw etc . , with complete accessories . make: mieco , location: indian air force station jorhat assam , supply of manual type tyre bead breaker kit . make: sarv , supply and installation of arc welding machine: arc welding machine 200 amps air cooled , 3 phase , with electrode holder , pair of leather hand gloves , helment with welding glass , incoming copper cable of 20 meters of 4 core x 4 sq . mm ( cable code: yy ) , 2 meters 3 core x 16 sq . mm copper welding cable with lugs , 2 meters 3 core x 16 sq . mm earthing copper cable with heavy duty earth clamp and lugs , wire brush , chipping hammer . make: electroweld weldarc . , supply of installation accessories: consists of 1 ) composite pipe size : 1 { 2025 20x25mm ) 40 mtrs . 2 ) female tee { 2025x1 / 2 } 12 no . 3 ) female elbow { 2025x1 / 2 } 4 no . 4 ) reduced nipple { 2025x1 / 2 } 8 no . 5 ) rounding tools 1 no . 6 ) plastic pipe chamfer 1 no . 7 ) pipe cutter 1 no . 8 ) external spring 1 no . 9 ) internal spring 1 no . 10 ) heavy duty clamp 100nos . set : consisting of screw nail 100 nos . , wooden gatta 1 100 nos . 11 ) flexible pipe 4mtr . long 3 / 8 id with end fitting 1 / 2 female thread 2 mtr 12 ) ball valve 1 / 2 12 no . 13 ) quick coupler 40 sma 16 no . 14 ) quick coupler 40 spa 16 no . 15 ) quick coupler adopter 20 pma 4 no . 16 ) brass hex nipple 1 / 2 x 1 / 2 12 no . 17 ) brass pu hose adopter 1 / 2 x 12mm 4 no . 18 ) brass pu hose adopter 1 / 4 x 12mm 4 no . 19 ) pu tube 8 mm x12 mm 50 mtrs 20 ) pu hose 8 mm x12 mm 15 mtrs . long coiled with end fittings 1 no . 21 ) quick coupler 40 ppa 6 no . 22 ) 1set of fittins for sand blasting machine & tyre inflator 1 no . 23 ) lubricator 1 / 2 1 no . 24 ) air tool lubricant 500ml vg 22 2 no . 25 ) auto drain valve 1 no . 26 ) micro / fine filter 1 no . 27 ) pre filter 1 no . 28 ) weather proof ( ip 67 ) non metallic type 20 a , 2p+e industrial plug & socket with 25 a sp mcb ( 10ka , d , curve ) along with sheet steel enclosure & accessories ( legrand / nine electric / schneider electric / l&t makes ) . 02 nos . 29 ) 16a 3 pin plug top ( anchor / legrand / mk makes ) 06 nos . 30 ) 12 module modular pvc box with modular cover plates , switch plates and accessories ( anchor / legrand / mk makes ) 02 nos . 31 ) 16a modular switch ( anchor / legrand / mk makes ) 06 nos . 32 ) 5 / 15a 5 pin modular socket ( anchor / legrand / mk makes ) 06 nos . 33 ) modular blanking plates 05 nos . 34 ) 4 . 0 sq . mm ring type cu lugs 16 nos . 35 ) insulation tapes ( red / yellow / blue / black / green ) 02 rolls of each colour . , supply and installation of electrically driven submersible sludge pump of capacity 1 hp , single phase , class f insulation , ip 68 protection , with minimum 10 meters head , stainless steel pump body , ss shaft , automatic on off , float switch , over load protection , non return valve , 1 1 / 2 inch nylon hose pipe of 30 meters for pump discharge with clamps , screws , tapes , installation accessories , 10 meters of 3 core x 2 . 5 sq . mm copper cable for inlet power connection to pump , 5 meters nylon rope . make: kirloskar , supply and installation of fuel trnsfr pmp , 12vdc , mieco mdl dyb 40dc , with inlet pipe nylon of 2 mtrs with fixing clamp , outlet pipe nylon of 5 mtrs with clamp , fuel gun , battery connecting wire of 5 mtrs with clips , clamping accessories , tape , clamps , screw etc . , with complete accessories . make: mieco...

Bharat Electronics Limited - Karnataka

22189211 procurement of modern service garage tools for iaf station, tejpur, and jorhat assam state: supply of manual type tyre bead breaker kit . make: sarv , supply and installation of arc welding machine: arc welding machine 200 amps air cooled , 3 phase , with electrode holder , pair of leather hand gloves , helment with welding glass , incoming copper cable of 20 meters of 4 core x 4 sq . mm ( cable code: yy ) , 2 meters 3 core x 16 sq . mm copper welding cable with lugs , 2 meters 3 core x 16 sq . mm earthing copper cable with heavy duty earth clamp and lugs , wire brush , chipping hammer . make: electroweld weldarc . , supply of installation accessories: consists of 1 ) composite pipe size : 1 { 2025 20x25mm ) 40 mtrs . 2 ) female tee { 2025x1 / 2 } 12 no . 3 ) female elbow { 2025x1 / 2 } 4 no . 4 ) reduced nipple { 2025x1 / 2 } 8 no . 5 ) rounding tools 1 no . 6 ) plastic pipe chamfer 1 no . 7 ) pipe cutter 1 no . 8 ) external spring 1 no . 9 ) internal spring 1 no . 10 ) heavy duty clamp 100nos . set : consisting of screw nail 100 nos . , wooden gatta 1 100 nos . 11 ) flexible pipe 4mtr . long 3 / 8 id with end fitting 1 / 2 female thread 2 mtr 12 ) ball valve 1 / 2 12 no . 13 ) quick coupler 40 sma 16 no . 14 ) quick coupler 40 spa 16 no . 15 ) quick coupler adopter 20 pma 4 no . 16 ) brass hex nipple 1 / 2 x 1 / 2 12 no . 17 ) brass pu hose adopter 1 / 2 x 12mm 4 no . 18 ) brass pu hose adopter 1 / 4 x 12mm 4 no . 19 ) pu tube 8 mm x12 mm 50 mtrs 20 ) pu hose 8 mm x12 mm 15 mtrs . long coiled with end fittings 1 no . 21 ) quick coupler 40 ppa 6 no . 22 ) 1set of fittins for sand blasting machine & tyre inflator 1 no . 23 ) lubricator 1 / 2 1 no . 24 ) air tool lubricant 500ml vg 22 2 no . 25 ) auto drain valve 1 no . 26 ) micro / fine filter 1 no . 27 ) pre filter 1 no . 28 ) weather proof ( ip 67 ) non metallic type 20 a , 2p+e industrial plug & socket with 25 a sp mcb ( 10ka , d , curve ) along with sheet steel enclosure & accessories ( legrand / nine electric / schneider electric / l&t makes ) . 02 nos . 29 ) 16a 3 pin plug top ( anchor / legrand / mk makes ) 06 nos . 30 ) 12 module modular pvc box with modular cover plates , switch plates and accessories ( anchor / legrand / mk makes ) 02 nos . 31 ) 16a modular switch ( anchor / legrand / mk makes ) 06 nos . 32 ) 5 / 15a 5 pin modular socket ( anchor / legrand / mk makes ) 06 nos . 33 ) modular blanking plates 05 nos . 34 ) 4 . 0 sq . mm ring type cu lugs 16 nos . 35 ) insulation tapes ( red / yellow / blue / black / green ) 02 rolls of each colour . , supply and installation of electrically driven submersible sludge pump of capacity 1 hp , single phase , class f insulation , ip 68 protection , with minimum 10 meters head , stainless steel pump body , ss shaft , automatic on off , float switch , over load protection , non return valve , 1 1 / 2 inch nylon hose pipe of 30 meters for pump discharge with clamps , screws , tapes , installation accessories , 10 meters of 3 core x 2 . 5 sq . mm copper cable for inlet power connection to pump , 5 meters nylon rope . make: kirloskar , supply and installation of fuel trnsfr pmp , 12vdc , mieco mdl dyb 40dc , with inlet pipe nylon of 2 mtrs with fixing clamp , outlet pipe nylon of 5 mtrs with clamp , fuel gun , battery connecting wire of 5 mtrs with clips , clamping accessories , tape , clamps , screw etc . , with complete accessories . make: mieco , location: indian air force station jorhat assam , supply of manual type tyre bead breaker kit . make: sarv , supply and installation of arc welding machine: arc welding machine 200 amps air cooled , 3 phase , with electrode holder , pair of leather hand gloves , helment with welding glass , incoming copper cable of 20 meters of 4 core x 4 sq . mm ( cable code: yy ) , 2 meters 3 core x 16 sq . mm copper welding cable with lugs , 2 meters 3 core x 16 sq . mm earthing copper cable with heavy duty earth clamp and lugs , wire brush , chipping hammer . make: electroweld weldarc . , supply of installation accessories: consists of 1 ) composite pipe size : 1 { 2025 20x25mm ) 40 mtrs . 2 ) female tee { 2025x1 / 2 } 12 no . 3 ) female elbow { 2025x1 / 2 } 4 no . 4 ) reduced nipple { 2025x1 / 2 } 8 no . 5 ) rounding tools 1 no . 6 ) plastic pipe chamfer 1 no . 7 ) pipe cutter 1 no . 8 ) external spring 1 no . 9 ) internal spring 1 no . 10 ) heavy duty clamp 100nos . set : consisting of screw nail 100 nos . , wooden gatta 1 100 nos . 11 ) flexible pipe 4mtr . long 3 / 8 id with end fitting 1 / 2 female thread 2 mtr 12 ) ball valve 1 / 2 12 no . 13 ) quick coupler 40 sma 16 no . 14 ) quick coupler 40 spa 16 no . 15 ) quick coupler adopter 20 pma 4 no . 16 ) brass hex nipple 1 / 2 x 1 / 2 12 no . 17 ) brass pu hose adopter 1 / 2 x 12mm 4 no . 18 ) brass pu hose adopter 1 / 4 x 12mm 4 no . 19 ) pu tube 8 mm x12 mm 50 mtrs 20 ) pu hose 8 mm x12 mm 15 mtrs . long coiled with end fittings 1 no . 21 ) quick coupler 40 ppa 6 no . 22 ) 1set of fittins for sand blasting machine & tyre inflator 1 no . 23 ) lubricator 1 / 2 1 no . 24 ) air tool lubricant 500ml vg 22 2 no . 25 ) auto drain valve 1 no . 26 ) micro / fine filter 1 no . 27 ) pre filter 1 no . 28 ) weather proof ( ip 67 ) non metallic type 20 a , 2p+e industrial plug & socket with 25 a sp mcb ( 10ka , d , curve ) along with sheet steel enclosure & accessories ( legrand / nine electric / schneider electric / l&t makes ) . 02 nos . 29 ) 16a 3 pin plug top ( anchor / legrand / mk makes ) 06 nos . 30 ) 12 module modular pvc box with modular cover plates , switch plates and accessories ( anchor / legrand / mk makes ) 02 nos . 31 ) 16a modular switch ( anchor / legrand / mk makes ) 06 nos . 32 ) 5 / 15a 5 pin modular socket ( anchor / legrand / mk makes ) 06 nos . 33 ) modular blanking plates 05 nos . 34 ) 4 . 0 sq . mm ring type cu lugs 16 nos . 35 ) insulation tapes ( red / yellow / blue / black / green ) 02 rolls of each colour . , supply and installation of electrically driven submersible sludge pump of capacity 1 hp , single phase , class f insulation , ip 68 protection , with minimum 10 meters head , stainless steel pump body , ss shaft , automatic on off , float switch , over load protection , non return valve , 1 1 / 2 inch nylon hose pipe of 30 meters for pump discharge with clamps , screws , tapes , installation accessories , 10 meters of 3 core x 2 . 5 sq . mm copper cable for inlet power connection to pump , 5 meters nylon rope . make: kirloskar , supply and installation of fuel trnsfr pmp , 12vdc , mieco mdl dyb 40dc , with inlet pipe nylon of 2 mtrs with fixing clamp , outlet pipe nylon of 5 mtrs with clamp , fuel gun , battery connecting wire of 5 mtrs with clips , clamping accessories , tape , clamps , screw etc . , with complete accessories . make: mieco...

Military Engineer Services - Karnataka

22135702 cleaning of oh reservoir , service water tank , ug sumps and connected works at chaf bangalore , de watering , removing all mosses , algae and dirt from internal walls , floors & mouths of pipes of rcc overhead reservoir/ under ground sump by using steel wire brush and cleaning with high pressure industrial vacuum cleaner including removing of dirty water completely using sludge pump set and disposing off the same to a safe distance and applying of anti bacterial sterilization spray to internal surfaces using zero bacterial compound ( sodium hypochlorte ) or equivalent approved chemical complete and writing the date of cleaning on outside of tank/ sump using synthetic enamel paint of white colour over black background with letters of schze 100mm height x 100mm breadth complete all as specified and directed for the oh reservoir of 75000 gallons capacity with 24 metre staging all as specified and directed . , all as per sch item no 01 here in above but for overhead reservoir 50 , 000 gallons capacity with staging exceeding 15 metres and not exceeding 24 metres all as specified and directed . , all as per sch item no 01 here in above but for overhead reservoir 15 , 000 gallons capacity with 6 metres staging all as specified and directed . , all as per sch item no 01 here in above but for overhead reservoir 5000 gallons capacity with staging of 6 metres all as specified and directed . , all as per sch item no 01 here in above but for ug sump 2 , 00 , 000 gallons capacity all as specified and directed . , all as per sch item no 01 here in above but for ug sump 1 , 50 , 000 gallons capacity all as specified and directed . , all as per sch item no 01 here in above but for ug sump 1 , 25 , 000 gallons capacity all as specified and directed . , all as per sch item no 01 here in above but for ug sump 20 , 000 gallons capacity all as specified and directed . , all as per sch item no 01 here in above but for ug sump 10 , 000 gallons capacity all as specified and directed . , de watering , removing all mosses , algae and dirt from internal walls , floors & mouths of pipes of rcc overhead tanks ( service tanks ) by using steel wire brush and cleaning with high pressure industrial vacuum cleaner including removing of dirty water completely using sludge pump set and disposing off the same to a safe distance and applying of anti bacterial sterilization spray to internal surfaces using zero bacterial compound ( sodium hypochlorte ) or equivalent approved chemical complete and writing the date of cleaning on outside of tank using synthetic enamel paint of white colour over black background with letters of size 50mm height x 50mm breadth , complete all as specified and directed for oh service tank upto 500 litres capacity all as specified and directed . , all as per sch item no 10 here in above but for oh service tank exceeding 500 litres and not exceeding 1000 ltrs capacity all as specified and directed . , all as per sch item no 10 here in above but for oh service tank exceeding 1000 litres and not exceeding 2000 ltrs capacity all as specified and directed . , all as per sch item no 10 here in above but for oh service tank exceeding 2000 litres and not exceeding 5000 ltrs capacity all as specified and directed . , de watering , removing all mosses , algae and dirt from internal walls , floors & mouths of pipes of pvc overhead tanks ( service tanks ) and cleaning with high pressure industrial vacuum cleaner including removing of dirty water completely using sludge pump set and disposing off the same to a safe distance and applying of anti bacterial sterilization spray to internal surfaces using zero bacterial compound ( sodium hypochlorte ) or equivalent approved chemical complete and writing the date of cleaning on outside of tank using synthetic enamel paint of white colour over black background with letters of size 50mm height x 50mm breadth , complete all as specified and directed for oh service tank upto 500 litres capacity all as specified and directed . , all as per sch item no 14 here in above but for oh service tank exceeding 500 litres and not exceeding 1000 ltrs capacity all as specified and directed . , all as per sch item no 14 here in above but for oh service tank exceeding 1000 litres and not exceeding 2000 ltrs capacity all as specified and directed . , all as per sch item no 14 here in above but for oh service tank exceeding 2000 litres but not exceeding 5000ltr capacity . note for sl sch item no 01 to 17: ( i ) any damage caused to tank , lid , ball valve , pipe line and connected items during cleaning shall be repaired or replaced by the contractor without any extra cost . ( ii ) any damage caused to fresh water line / inlet tank pipe line over the building and connecated item shall be repaired or replaced accordingly . ( iii ) after tank cleaning register to be mantained for obtaining signature from users and submitted to concernt sub divison before processchng rar . ( iv ) cleaning of tank shall be carried out as per site requirement complete all as specified and directed . , s&f in replacement gun metal gate or globe valve , heavy duty , isi marked , with iron wheel head screwed both end for 15mm bore gi tubes , fixed in repairs , all as specified and as directed . , all as per sch item no . 18 here in above but for 20mm bore gi tubes all as specified and as directed , all as per item no . 18 herein before but for 25mm bore gi tubes all as specified and as directed , all as per sch item no . 18 herein before but for 40mm bore gi tubes all as specified and as directed , all as per sch item no . 18 herein before but for 50mm bore gi tubes all as specified and as directed , s&f in replacement ptmt ball valve , high pressure , with epoxy coated aluminium rod and high denschty plastic ball screwed for 15mm bore gi tubes , fixed in repairs , all as specified and as directed . , all as per sch item no . 23 here in above but for 20mm bore gi tubes all as specified and directed . , all as per sch item no . 23 here in above but for 25mm bore gi tubes all as specified and directed . , all as per sch item no . 23 here in above but for 40mm bore gi tubes all as specified and directed . , all as per sch item no . 23 here in above but for 50mm bore gi tubes all as specified and directed . , s&f in replacement pvc lid suitable for pvc tanks of capacity 500/1000/2000 litres , fixed in repairs all as specified and as directed . , taking down steel tubing and connections of size 15mm bore including cleaning , threading for re fixing or removal of unserviceable pipe from site of work complete all as directed . , all as per sch item no . 29 here in above but 20mm bore all as specified and directed . . , all as per sch item no . 29 here in above but 25mm bore all as specified and directed . , all as per sch item no . 29 here in above but 40 & 50mm bore all as specified and directed . , re fixing 15mm bore gi tubing , medium grade with provn of new fittings as required and fixing accessories in new or old position ( walls , ceiling floor etc ) including testing complete all as directed . , all as sch item no 33 herein before but 20mm bore all as specified and directed . , all as sch item no 33 herein before but 25mm bore all as specified and directed . , all as sch item ...

Military Engineer Services - Karnataka

21859159 cleaning of oh reservoir , service water tank , ug sumps and connected works at chaf bangalore , de watering , removing all mosses , algae and dirt from internal walls , floors & mouths of pipes of rcc overhead reservoir/ under ground sump by uschng steel wire brush and cleaning with high pressure industrial vacuum cleaner including removing of dirty water completely uschng sludge pump set and disposchng off the same to a safe distance and applying of anti bacterial sterilization spray to internal surfaces uschng zero bacterial compound ( sodium hypochlorte ) or equivalent approved chemical complete and writing the date of cleaning on outschde of tank/ sump uschng synthetic enamel paint of white colour over black background with letters of schze 100mm height x 100mm breadth complete all as specified and directed for the oh reservoir of 75000 gallons capacity with 24 metre staging all as specified and directed . , all as per sch item no 01 here in above but for overhead reservoir 50 , 000 gallons capacity with staging exceeding 15 metres and not exceeding 24 metres all as specified and directed . , all as per sch item no 01 here in above but for overhead reservoir 15 , 000 gallons capacity with 6 metres staging all as specified and directed . , all as per sch item no 01 here in above but for overhead reservoir 5000 gallons capacity with staging of 6 metres all as specified and directed . , all as per sch item no 01 here in above but for ug sump 2 , 00 , 000 gallons capacity all as specified and directed . , all as per sch item no 01 here in above but for ug sump 1 , 50 , 000 gallons capacity all as specified and directed . , all as per sch item no 01 here in above but for ug sump 1 , 25 , 000 gallons capacity all as specified and directed . , all as per sch item no 01 here in above but for ug sump 20 , 000 gallons capacity all as specified and directed . , all as per sch item no 01 here in above but for ug sump 10 , 000 gallons capacity all as specified and directed . , de watering , removing all mosses , algae and dirt from internal walls , floors & mouths of pipes of rcc overhead tanks ( service tanks ) by uschng steel wire brush and cleaning with high pressure industrial vacuum cleaner including removing of dirty water completely uschng sludge pump set and disposchng off the same to a safe distance and applying of anti bacterial sterilization spray to internal surfaces uschng zero bacterial compound ( sodium hypochlorte ) or equivalent approved chemical complete and writing the date of cleaning on outschde of tank uschng synthetic enamel paint of white colour over black background with letters of schze 50mm height x 50mm breadth , complete all as specified and directed for oh service tank upto 500 litres capacity all as specified and directed . , all as per sch item no 10 here in above but for oh service tank exceeding 500 litres and not exceeding 1000 ltrs capacity all as specified and directed . , all as per sch item no 10 here in above but for oh service tank exceeding 1000 litres and not exceeding 2000 ltrs capacity all as specified and directed . , all as per sch item no 10 here in above but for oh service tank exceeding 2000 litres and not exceeding 5000 ltrs capacity all as specified and directed . , de watering , removing all mosses , algae and dirt from internal walls , floors & mouths of pipes of pvc overhead tanks ( service tanks ) and cleaning with high pressure industrial vacuum cleaner including removing of dirty water completely uschng sludge pump set and disposchng off the same to a safe distance and applying of anti bacterial sterilization spray to internal surfaces uschng zero bacterial compound ( sodium hypochlorte ) or equivalent approved chemical complete and writing the date of cleaning on outschde of tank uschng synthetic enamel paint of white colour over black background with letters of schze 50mm height x 50mm breadth , complete all as specified and directed for oh service tank upto 500 litres capacity all as specified and directed . , all as per sch item no 14 here in above but for oh service tank exceeding 500 litres and not exceeding 1000 ltrs capacity all as specified and directed . , all as per sch item no 14 here in above but for oh service tank exceeding 1000 litres and not exceeding 2000 ltrs capacity all as specified and directed . , all as per sch sch item no 14 here in above but for oh service tank exceeding 2000 litres but not exceeding 5000ltr capacity . note for sl sch item no 01 to 17: ( i ) any damage caused to tank , lid , ball valve , pipe line and connected items during cleaning shall be repaired or replaced by the contractor without any extra cost . ( ii ) any damage caused to fresh water line / inlet tank pipe line over the building and connecated item shall be repaired or replaced accordingly . ( iii ) after tank cleaning register to be mantained for obtaining schgnature from users and submitted to concernt sub divischon before processchng rar . ( iv ) cleaning of tank shall be carried out as per schte requirement complete all as specified and directed . , s&f in replacement gun metal gate or globe valve , heavy duty , isch marked , with iron wheel head screwed both end for 15mm bore gi tubes , fixed in repairs , all as specified and as directed . , all as per sch item no . 18 here in above but for 20mm bore gi tubes all as specified and as directed , all as per item no . 18 herein before but for 25mm bore gi tubes all as specified and as directed , all as per sch item no . 18 herein before but for 40mm bore gi tubes all as specified and as directed , all as per sch item no . 18 herein before but for 50mm bore gi tubes all as specified and as directed , s&f in replacement ptmt ball valve , high pressure , with epoxy coated aluminium rod and high denschty plastic ball screwed for 15mm bore gi tubes , fixed in repairs , all as specified and as directed . , all as per sch item no . 23 here in above but for 20mm bore gi tubes all as specified and directed . , all as per sch item no . 23 here in above but for 25mm bore gi tubes all as specified and directed . , all as per sch item no . 23 here in above but for 40mm bore gi tubes all as specified and directed . , all as per sch item no . 23 here in above but for 50mm bore gi tubes all as specified and directed . , s&f in replacement pvc lid suitable for pvc tanks of capacity 500/1000/2000 litres , fixed in repairs all as specified and as directed . , taking down steel tubing and connections of size 15mm bore including cleaning , threading for re fixing or removal of unserviceable pipe from site of work complete all as directed . , all as per sch item no . 29 here in above but 20mm bore all as specified and directed . . , all as per sch item no . 29 here in above but 25mm bore all as specified and directed . , all as per sch item no . 29 here in above but 40 & 50mm bore all as specified and directed . , re fixing 15mm bore gi tubing , medium grade with provn of new fittings as required and fixing accessories in new or old position ( walls , ceiling floor etc ) including testing complete all as directed . , all as sch item no 33 herein before but 20mm bore all as specified and directed . , all as sch item no 33 herein before but 25mm bore all as specified and dir...

Karnataka Urban Water Supply And Drainage Board - Karnataka

11062916 part ii: construction, supply. installation, testing and commissioning of civil, mechanical, electrical and instrumentation works of 5.13 mid capacity sewage treatment plant of sequential batch reactor ( sbr ) technology including collection chamber with distribution channel, chlorine contact tank, sludge sump, sludge pump house, chlorination room and tonner room, centrifuge house, administration building including compound wall, service road, staff quarters, landscaping and yard lighting. ...

Karnataka Urban Water Supply And Drainage Board - Karnataka

11042508 under ground drainage scheme to shivamogga city under amrutpart i: providing and laying pvc u / swg / rcc / dwc sewerlines with rcc / bbm / hdpe manholes and providing house service connections in the additional areas, di rising main, rehabilitation of existing sewerlines and construction of wetwells. part ii: construction, supply, installation, testing and commissioning of civil, mechanical, electrical and instrumentation works of 5.13 mld capacity sewage treatment plant of sequential batch reactor ( sbr ) technology including collection chamber with distribution channel, chlorine contact tank, sludge sump, sludge pump house, chlorination room and tonner room, centrifuge house, administration building including compound wall, service road, staff quarters, landscaping and yard lighting part iii: supply, erection, electrification and commissioning of suitable capacity submersible non clog sewage pumpsets along with allied accessories for wetwellspart iv: operation and maintenance of the assets built under this contract for a period of 5 years ( including one year defect liability period )...

Karnataka Urban Water Supply And Drainage Board - Karnataka

10896259 under ground drainage scheme to shivamogga city under amrut part 2 construction, supply , installation testing and commissioning of civil mechanical , electrical and instruments works of 5.13 mld capacit sewage treatment plant of sequential batch reactor isbri technology including collection chamber with distribution channel , chorine contract tank , sludge sump , sludge pump house , chlorination room and tonner room , certitude house , administration building including compound wall , services road , staff quarters , landscaping and yard lighting...

Karnataka Urban Water Supply And Drainage Board - Karnataka

9935548 tender for under ground drainage scheme to shivamogga city: part ii: construction, supply, installation, testing and commissioning of civil, mechanical, electrical and instrumentation works of 5.13 mld capacity sewage treatment plant of sequential batch reactor technology including collection chamber with distribution channel, chlorine contact tank, sludge sump, sludge pump house, administration building including compound wall, service road, staff quarters, landscaping and yard lighting....

Karnataka Urban Water Supply And Drainage Board - Karnataka

9295960 tender for construction of 10m dia wetwell cum pumphouse 2 at chikkakere with inlet, screen chamber & outlet chamber, providing and laying of 600mm dia di k7 rising main, construction of 8x6m diesel generator room, construction of compound wall and providing aspitit toad to sewage treatment plant in hoskote town. part b: ( lumps= basis ) construction, supply, installation, testing & commissioning of civil, mechanical, electrical and instrumentation works of 8.52 mld capacity sewage treatment plant of sequential batch reactor ( sbr ) technology including stilling chamber, screen chamber with distribution channel, sba basins, chlotine contact tank, chlorination room, sludge sump. sludge pump house, centrifuge house, administration building at hoskote town. under ugc scheme to hoskote town under uidst....

Karnataka Urban Water Supply And Drainage Board - Karnataka

9276406 part a (item rate) construction of 10m dia wetwell cum pumphouse 2 at chikkakere with inlet, screen chamber and outlet chamber, providing and laying of 600mm dia di k7 rising main, construction of 8x6m diesel generator room, construction of compound wall and providing asphalt road to sewage treatment plant in hoskote town under under ground drainage scheme to hoskote town under uidst. part b (lumpsum basis) construction, supply, installation, testing and commissioning of civil, mechanical, electrical and instrumentation works of 8.52 mld capacity sewage treatment plant of sequential batch reactor (sbr) technology including stilling chamber, screen chamber with distribution channel, sperical repair basins, chlorine contact tank, chlorination room, sludge sump, sludge pump house, centrifuge house, administration building at hoskote town under under ground drainage scheme to hoskote town under uidst. (hsk stp 01)...

Karnataka Urban Water Supply And Drainage Board - Karnataka

6716704 providing and laying of 500mm dia rccoutall sewer, construction of ptu, 8.0m dia wetwell cum pump house, providing and laying of 350mm dia di rising main from wetwell to collection chamber, diesel generator room, compound wall etc b construction supply installation, testing and commissioning of civil, mechanical, electrical and instrumentation works of 4.0 mld capacity sewage treatment plant of sequential batch reactor technology including collection chamber with distribution channel, chlorine contact tank, sludge pump, sludge pump house, chlorination room and tonner room operation and maintenance for one year ...